Truma Mover XT2 User Manual

5EN
Only MoverXT2 control knob
It is not possible to turn a caravan with a two-axle chassis on
the spot.
Control knob and slide control, MoverXT / XT2
(Cornering forward or backward to the right or left)
– Control knob to the right and slide control forward –>
caravan moves forward in the direction of the drawbar in a
right-hand bend
– Control knob to the left and slide control forward –>
caravan moves forward in the direction of the drawbar in a
left-hand bend
– Control knob to the right and slide control backward –>
caravan moves backward in the opposite direction to the
drawbar in a right-hand bend
– Control knob to the left and slide control backward –>
caravan moves backward in the opposite direction to the
drawbar in a left-hand bend
The more the slide control is pushed towards the end stop,
the faster the movement.
The more the control knob is turned, the smaller the turning
radius. The caravan can be manoeuvred accurately by using
the slide control and control knob at the same time. Due to
the design, it is not possible to manoeuvre in very tight bends
with a two-axle chassis.
Engaging and disengaging
The drive rollers are engaged and disengaged on the
caravan wheels by means of the remote control.
h = Two-handed operation disengagement of drive rollers
(drive rollers swing away from tyres)
i = Two-handed operation engagement of drive rollers
(drive rollers swing towards tyres)
Before disengaging, make sure that the caravan can-
not roll away. Engage the parking brake and / or secure
against rolling with wedges.
To engage/ disengage the drive rollers, always press both
buttons simultaneously – for about 3 seconds (safety delay)
– until you hear an acoustic signal and the drive rollers start to
engage/ disengage.
During engagement/ disengagement, the LED2 flashes and
you can release the buttons. When the drive rollers reach their
end position, you will hear a double acoustic signal.
The drive commands with the control knob and slide
control are executed only when the drive rollers are com-
pletely engaged or disengaged. If the engagement/ disen-
gagement process is interrupted, it has to be restarted and
completed before more drive commands can be executed.
If the two buttons for disengaging are pressed while the
rollers are engaging, engaging is interrupted, the drive
rollers are disengaged and automatically move to their end
position.
The remote control switches itself off automatically after ap-
prox. 3minutes if none of the buttons are pressed. The green
LED 4 goes out.
To reactivate the remote control, move the slide switch
to “Off”
and then back to “On” after approximately
2seconds.
There is no “On / Off” switch on the caravan itself.
The side slide switch on the remote control (ON / OFF) also
acts as an “Emergency Stop switch”. In case of noticeable
problems, such as uncontrolled behaviour of the manoeuvring
system, immediately switch the slide switch on the side to
“Off”.
The remote control can be switched on again only if it
has been switched off for at least 2 seconds. If the re-
mote control is switched off and on again quickly, it remains
switched off.
Remote control LED flashing code and
acoustic signal
LED 1 red Displays the charging status of the caravan
battery
good LED off
weak LED lights up
flat LED on and LED 3 indicates a fault
LED 2 yellow lights up in the event of a temporary malfunc-
tion, and an acoustic signal is also emitted in
the event of overcurrent / overtemperature. The
power is automatically reduced. Allow the sys-
tem to cool down.
flashes when the Mover is engaged and the
control unit or remote control is switched off.
Anacoustic signal is also emitted.
flashes during engaging/ disengaging
flashes when switched on if the engaging/ dis-
engaging process was not completed before it
was switched off last time. An acoustic signal is
also emitted. Restart and complete the engag-
ing/ disengaging process. Only then can drive
commands be executed with the control knob or
slide control.
LED 3 red lights up in the event of a persistent fault, and
an acoustic signal is also emitted, e.g. in the
event of a faulty drive motor, engage the parking
brake. See “Troubleshooting”
Green LED 4 flashes slowly until the radio connection is es-
tablished when the remote control is switched
on.
flashes four times with an acoustic signal if the
connection to the control unit is not established
within 10 seconds after the remote control is
switched on. The remote control then switches
off.
lights up when remote control is ready for
operation and the data link is stable
flashes four times when the drive rollers are dis-
engaged and the control unit is switched off. The
remote control then switches off.
flashes four times with an acoustic signal if no
button is pressed on the remote control within
3minutes The remote control then switches off.
flashes four times with an acoustic signal if the
radio connection is interrupted. The remote con-
trol then switches off.
All LEDs “off” and no acoustic signal
System off
(check remote control batteries)
Replacing remote control batteries
Use only leak-proof micro-batteries with a steel outer casing,
type LR 03, AAA, AM 4, MN 2400 (1.5 V).
When inserting new batteries, take care not to reverse the
positive and negative terminals.

Truma Mover XT2 Specifications

General

Brand	Truma
Model	Mover XT2
Category	Automobile Accessories
Language	English