How to solve wrinkle problems with a TSC MB240?
If you are experiencing a wrinkle problem with your TSC printer: * Refer to the next chapter. * Set a suitable density for good print quality. * Ensure the label guide touches the edge of the media guide.
How to remove a gray line on blank labels from a TSC MB240 Printer?
If there's a gray line on the blank label when using your TSC printer, clean the print head and the platen roller.
What to do if my TSC MB240 Printer is not printing?
If your TSC printer isn't printing, try the following: * Reconnect the cable to the interface or use a new cable. * Reset the wireless device setting. * Select the correct printer port in the driver. * Clean the printhead. * Turn off the printer and plug the connector in again. * Check your program for a PRINT command at the end of the file and ensure there is CRLF at the end of each command line.
How to fix missing print on the sides of labels with a TSC MB240 Printer?
If your TSC printer is missing printing on the left or right side of the label, set the correct label size.
What to do if my TSC MB240 shows 'No Paper'?
If your TSC printer indicates 'No Paper', you should: * Supply a new label roll. * Refer to the user’s manual for instructions on reinstalling the label roll. * Calibrate the gap/black mark sensor.
How to fix label feeding if it's unstable (skew) on my TSC printer?
If the label feeding is not stable (skew) when printing with your TSC printer: * If the label moves to the right, move the label guide to the left. * If the label moves to the left, move the label guide to the right.
How to fix a TSC MB240 Printer when the power indicator does not illuminate?
If the power indicator on your TSC printer is not illuminating: * Plug the power cord into both the printer and the outlet. * Switch the printer on.
What to do if my TSC MB240 Printer has a paper jam?
If your TSC printer has a paper jam, try the following: * Calibrate the media sensor. * Set the media size correctly. * Remove any stuck labels inside the printer mechanism.
How to fix paper jam in TSC Barcode Reader?
If your TSC Barcode Reader is experiencing paper jams, it could be due to a few reasons. First, the gap/black mark sensor may not be set properly; try calibrating the media sensor. Second, ensure that the label size is set correctly. Finally, labels may be stuck inside the printer mechanism; remove any stuck labels.
What to do if my TSC Barcode Reader displays 'No Ribbon'?
If your TSC Barcode Reader displays 'No Ribbon', it could be that the ribbon roll is depleted. Replace it with a new ribbon roll. Alternatively, the ribbon might be installed incorrectly. Consult the user’s manual for instructions on how to reinstall the ribbon correctly.
General| Print Method | Thermal Transfer/Direct Thermal |
|---|---|
| Resolution | 203 dpi |
| Processor | 32-bit RISC CPU |
| Operating Humidity | 25-85% non-condensing |
| Connectivity | USB 2.0, RS-232 |
| Media Sensor | Reflective, Transmissive |
| Media Type | Continuous, Die-cut, Black mark, Fan-fold, Notched |
| Media Width | 25.4 mm |
| Media Thickness | 0.06 mm |
| Media Core Diameter | 25.4 mm (1") |
| Media Max Roll Diameter | 127 mm (5") |
| Ribbon Width | 110 mm |
| Ribbon Length | 300 m |
| Ribbon Core Diameter | 25.4 mm (1 inch) |
| Power | 100 - 240 VAC, 50/60 Hz |
| Maximum Print Length | 9999 mm |
| Label Width | 25.4 mm |
| Label Thickness | 0.06 mm |
| Power Supply | 100-240V AC, 50-60Hz |
| Operating Temperature | 5°C - 40°C |
| Storage Temperature | -20°C - 60°C |
| Certifications | CE |
To Next Page
