What to do if I can’t download files to memory of my TSC TC210?
If you can't download files to the memory (FLASH / DRAM / CARD) of your TSC Barcode Reader, it's likely that the memory is full. Delete any unused files to free up space.
Why is my TSC TC210 Barcode Reader not printing?
If your TSC Barcode Reader isn't printing, first ensure the interface cable is securely connected; reconnect it or try a new cable. If using a wireless or Bluetooth connection, verify that the device is properly connected between the host and the printer. If you're using a serial cable, replace it with a pin-to-pin connected cable. Also, check that the correct printer port is selected in the Windows driver settings.
How to fix poor print quality on my TSC TC210?
To resolve poor print quality on your TSC Barcode Reader, start by reloading the ribbon and media to ensure they are correctly installed. Clean the print head to remove any dust or adhesive accumulation. Then, adjust the print density and print speed settings to optimize the print quality.
Why does my TSC TC210 Barcode Reader skip labels when printing?
If your TSC Barcode Reader is skipping labels during printing, ensure the label size is correctly specified in your settings. Then, calibrate the sensor using either the Auto Gap or Manual Gap options. Finally, clear any dust from the GAP/Black mark sensor using a blower.
What to do if there is no print on the label from my TSC TC210 Barcode Reader?
If there's no print on the label from your TSC Barcode Reader, ensure the label and ribbon are loaded correctly by following the loading instructions. Verify you're using the correct type of paper and ribbon, paying attention to the ribbon-inked side. Additionally, clean the print head, as the print density setting may be incorrect.
How to resolve irregular printing on my TSC TC210?
To address irregular printing on your TSC Barcode Reader, try turning the printer off and then on again to exit the dump mode. Also, verify and reset the RS-232 settings to ensure they are correct.
How to resolve wrinkle issues on my TSC Barcode Reader?
If you're experiencing wrinkle issues with your TSC Barcode Reader, adjust the printhead pressure to achieve optimal print quality. Also, ensure that the ribbon is installed correctly and that the label guides touch the edge of the media guide.
What to do if the cutter is not working on my TSC TC210 Barcode Reader?
If the cutter on your TSC Barcode Reader is not functioning, first ensure that the connector cable is properly plugged in. If the cutter is jammed, remove the label causing the jam. If these steps don't resolve the issue, the cutter PCB might be damaged, requiring a replacement of the cutter driver IC board.
How to fix a gray line on the blank label from my TSC Barcode Reader?
If your TSC Barcode Reader is showing a gray line on the blank label, the print head or the platen roller may be dirty. Try cleaning both the print head and the platen roller.
Why is label feeding unstable on my TSC TC210?
If the label feeding on your TSC Barcode Reader is unstable, causing skew during printing, adjust the media guides so they touch the edge of the media. If the label is moving to the right, move the label guide to the left, and vice versa.
Identifies external components of the TC210 and TC200 series printers.
Lists and identifies connectors on the main board.
Step-by-step guide for replacing LED/LCD module.
Step-by-step guide for replacing the main board.
Instructions for replacing the print head assembly.
General| Model | TC210 Series |
|---|---|
| Type | Barcode Printer |
| Operating System Compatibility | Windows, Linux, Mac |
| Resolution | 203 DPI (8 dots/mm) |
| Power Supply | External Universal Switching Power Supply |
| Processor | 32-bit RISC |
| Interface | USB 2.0 |
| Media type | Continuous, Die-Cut, Black Mark, Notch |
| Media core diameter | 1" (25.4 mm) |
| Label length | 5 ~ 2, 794 mm (0.2" ~ 110") |
| Power source | AC 100-240V, 50-60Hz |
| Input | AC 100-240V, 50-60Hz |
| Media width | 25.4 ~ 112 mm (1" ~ 4.4") |
| Media thickness | 0.0028" to 0.008" (0.07 mm to 0.2 mm) |
To Next Page
