TSC TTP-245C - User Manual

Other manuals for TSC TTP-245C

Service Manual33 pages

Questions and Answers

D
Devin HerreraAug 15, 2025
What to do if my TSC Barcode Reader is not printing?
- R
  Ryan Carter DDSAug 15, 2025
  If your TSC Barcode Reader is not printing, first reconnect the interface cable to ensure it's properly connected. If using a serial port, ensure the cable is pin-to-pin connected or replace it. Verify that the serial port settings are consistent between the host and printer, and correct the printer port in the Windows driver. Also, ensure the Ethernet IP, subnet mask, and gateway are configured correctly.
L
Linda OrtizAug 18, 2025
How to fix paper jam in TSC Barcode Reader?
- M
  Mr. Joseph StewartAug 18, 2025
  If your TSC Barcode Reader has a paper jam, calibrate the gap/black mark sensor. Ensure the label size is correctly set in your labeling software. Also, check for and remove any labels stuck inside the printer mechanism near the sensor area.
J
Jill FullerAug 21, 2025
How to improve print quality on my TSC Barcode Reader?
- R
  Robert AndradeAug 21, 2025
  If your TSC Barcode Reader is producing poor print quality, ensure the top cover is completely closed and latched properly on both sides. Reload the supply to make sure it is correctly loaded. If the issue persists, try changing the ribbon or label combination, as they may be incompatible. Finally, inspect the print head for dust or adhesives and clean it if necessary.
L
Lindsay RobinsonAug 25, 2025
How to check print head test pattern if head element is damaged on TSC Barcode Reader?
- A
  Anna DawsonAug 26, 2025
  Run a printer self-test on your TSC Barcode Reader and check the print head test pattern to see if any dots are missing.
D
Dustin RiveraAug 28, 2025
Why my TSC Barcode Reader shows no response?
- L
  Lisa WalkerAug 28, 2025
  If the TSC Barcode Reader shows no response, ensure the power switch is turned on. Check if the green LED is lit on the power supply; if not, the power supply might be broken. Verify that both power connections, from the cord to the supply and from the supply to the printer, are securely connected.
J
Jeffrey MyersSep 1, 2025
Why there is no print on the label from my TSC Barcode Reader?
- R
  rmartinezSep 1, 2025
  If there is no print on the label from your TSC Barcode Reader, check if the label or ribbon is loaded correctly by following the loading instructions. Also, make sure the ribbon hasn't run out and reload it if necessary.
S
Stephen PotterSep 4, 2025
What to do if my TSC Barcode Reader is continuously feeding labels?
- D
  David CaseSep 4, 2025
  If your TSC Barcode Reader is continuously feeding labels, initialize the printer and perform gap/black mark calibration.
M
Mrs. Crystal CooperSep 7, 2025
What to do if my TSC Barcode Reader is paused?
- G
  gabrielthomasSep 7, 2025
  If your TSC Barcode Reader is paused, press the FEED button to resume printing.
C
Christine PettySep 12, 2025
What to do if my TSC Barcode Reader is out of label or ribbon?
- M
  Matthew RobertsonSep 12, 2025
  If your TSC Barcode Reader is out of label or ribbon, load a new roll of label or ribbon following the instructions, then press the FEED button to resume printing. If the printer setting is not correct, initialize the printer using the “Power on Utility” or “Diagnostic Tool”.

Summary

Copyright Declaration

Introduction to TSC Bar Code Printers

Product Introduction

Overview of the TSC bar code printer's features and performance.

Compliance Standards

Lists the various safety and performance compliance standards met by the printer.

Printer Operations Overview

Unpacking and Inspection

Instructions for unpacking the printer and checking its contents.

Printer Component Identification

Front View Components

Identifies and labels the external components visible from the front of the printer.

Interior View Components

Details and labels the internal parts of the printer.

Rear View Ports and Connections

Identifies the ports and connectors located on the rear of the printer.

Printer Setup Procedures

Initial Printer Setup

Step-by-step guide for setting up the printer for the first time.

Opening and Closing the Top Cover

Instructions on how to safely open and close the printer's top cover.

Loading the Printer Ribbon

Detailed steps for installing a new ribbon into the printer.

Loading Printer Media

Basic Media Loading

Basic procedure for loading label media into the printer.

External Label Roll Mount Installation

Guide for installing the optional external roll mount for media.

Loading Media in Peel-off Mode

Instructions for loading media when using the peel-off module.

Loading Media in Cutter Mode

Instructions for loading media when using the cutter module.

Printer Diagnostic Tool

Starting the Diagnostic Tool

How to launch and begin using the printer's diagnostic utility software.

Printer Functions via Diagnostic Tool

Details on printer functions accessible through the diagnostic tool interface.

Ethernet Configuration Utility

Setup via USB Interface

Configuring the printer's Ethernet connection using a USB interface.

Setup via RS-232 Interface

Configuring the printer's Ethernet connection using an RS-232 interface.

Setup via Ethernet Interface

Configuring the printer's Ethernet connection directly via the network.

Installing the SD Memory Card

Printer LED and Button Functions

LED Indicator Guide

Explains the meaning of different LED colors and patterns.

Regular Button Operations

Describes the functions of the printer's main button during normal operation.

Power-On Utilities Overview

Introduces utilities accessed by pressing the button during power-on.

Ribbon and Sensor Calibration

Procedure for calibrating ribbon and gap/black mark sensors via power-on utility.

Self-test and Dump Mode Calibration

How to perform sensor calibration, self-test, and enter dump mode.

Printer Initialization

Steps to reset printer settings to factory defaults.

Configure Black Mark Sensor

How to configure and calibrate the black mark sensor for media detection.

Configure Gap Sensor

How to configure and calibrate the gap sensor for media detection.

Skipping AUTO.BAS Program

Method to bypass the automatic execution of the AUTO.BAS program.

Printer Troubleshooting Guide

LED Status Troubleshooting

Diagnosing printer issues based on the status of the LED indicator.

Print Quality Issues and Solutions

Common problems affecting print quality and their resolutions.

Printer Maintenance and Cleaning

TSC TTP-245C Specifications

General

Resolution	203 dpi
Print Width	4.09 inches
Memory	8 MB Flash
Interface	USB
Print Method	Thermal Transfer/Direct Thermal
Maximum Print Width	4.09 inches
Connectivity	USB
Supported Barcode Types	Code 39, Code 128, UPC-A, UPC-E, EAN-13, EAN-8, Interleaved 2 of 5, Codabar
Power Supply	100-240V AC, 50/60Hz