TSI Instruments 3080L - Page 144

Index–5
related literature (continued)
Model 3772/3771 Condensation Particle Counter
manual, xvii
Model 3775 Condensation Particle Counter
manual, xvii
Model 3776 Ultrafine Condensation Particle
Counter manual, xvii
Model 3782 Water-based Condensation Particle
Counter manual, xvii
Model 3785 Water-based Condensation Particle
Counter manual, xvii
Model 3786 Ultrafine Water-based Condensation
Particle Counter manual, xvii
Model 3936 Scanning Mobility Particle Sizer
(SMPS) Spectrometer manual, xvii
removal
high-voltage controller, 6-19
Model 3077A/3077 Kr-85 Neutralizer, 6-12
resources. (
see references)
S
safety, xiii
caution symbol, xv
labels, xiii
lifting caution, xv
save button, D-10
Scanning Electrical Mobility Spectrometer
(SEMS), B-2
schematic
Electrostatic Classifier with Long DMA, B-6
Electrostatic Classifier with Nano DMA in dual
blower mode, B-8
Electrostatic Classifier with Nano DMA in single
blower mode, B-7
Model 3081 Long DMA, 4-3
Model 3085 Nano DMA, 4-5
serial data commands, C-1
baud rate, C-3
combined set commands, C-7
command quick reference, C-4
commands, C-3
making connection, C-1
parity, C-3
pin connectors, C-1
read command, C-4
definition, C-5
read firmware version, C-6
read flags, C-7
read flow rates, C-5
read measured values, C-6
read model name, C-7
read on time, C-7
read pressure, C-5
read temperature, C-6
read user settings, C-6
set auxiliary output, C-11
set bypass flow rate, C-8
set calibration bypass parameter A, C-10
set calibration bypass parameter B, C-11
set calibration impactor parameter A, C-11
serial data commands
(continued)
set calibration impactor parameter B, C-11
set commands, C-4
set DMA parameter, C-12
set flow calibration algorithm, C-8
set flow calibration table, C-8
set flow calibration table correct, C-9
set flow mode, C-8
set high voltage, C-7
set offset bit value of flow sensor, C-10
set or read impactor serial number, C-9
set particle diameter, C-7
set sheath flow calibration parameter A, C-10
set sheath flow calibration parameter B, C-10
set sheath flow rate, C-8
set voltage mode, C-7
troubleshooting input, C-5
serial port, 3-4
communication settings, D-3
connector on back of Classifier, C-2
pin designations, C-2
service, 6-1
returning Classifier, 6-21
set auxiliary output, C-11
set bypass flow rate command, C-8
set calibration, D-6, D-9
set calibration button, D-10
set calibration bypass parameter A command, C-10
set calibration bypass parameter B command, C-11
set calibration impactor parameter A
command, C-11
set calibration impactor parameter B
command, C-11
set command, C-4
set DMA parameter, C-12
set flow calibration algorithm, C-8
set flow calibration table, C-8
set flow calibration table correct, C-9
set flow mode command, C-8
set offset bit value of flow sensor, C-10
set or read impactor serial number, C-9
set particle diameter command, C-7
set sheath flow calibration parameter A
command, C-10
set sheath flow calibration parameter B
command, C-10
set sheath flow rate command, C-8
set voltage mode command, C-7
setting up the Classifier, 2-1
setup tab, D-5
sheath air
3080L, A-2
3080N, A-3
sheath air flow controller, 5-7
sheath flow, A-1, D-6
calibration, D-7
sheath flow calibration, D-6
sheath flow controller, 3-9
sheath flow fitting, 3-6
sheath flow mode, 5-2
sheath flow port, 2-11, 2-14, 2-16
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com