What does ‘Low Heat’ mean on my Tuttnauer 2340E Laboratory Equipment?
If the message ‘Low Heat’ is displayed during heat up on your Tuttnauer Laboratory Equipment, it indicates a bad temperature sensor. If heating elements are remaining on instead of cycling on and off, call for a technician.
How to clean a very dirty chamber in my Tuttnauer 2340E Laboratory Equipment?
If the chamber of your Tuttnauer Laboratory Equipment is very dirty, use Chamber Brite ™ to clean the autoclave; very dirty machines may require two cleanings.
What to do if Tuttnauer 2340E Laboratory Equipment process fails during heating stage with a HIGH TEMP message?
If your Tuttnauer Laboratory Equipment process fails while initiating the heating stage and displays a HIGH TEMP message, try changing the setting of the thermostat.
How to troubleshoot Tuttnauer Laboratory Equipment machine not responding?
If your Tuttnauer Laboratory Equipment machine isn't responding, verify that the main switch is in the ‘On’ position, the power cord is properly connected to both the machine and the mains, and the circuit breaker hasn't tripped. Also, check the reset button on the cut-out thermostat.
What should I do if my Tuttnauer 2340E shows ‘Low Pres’?
If the 'Low Pres' message is displayed on your Tuttnauer Laboratory Equipment, clean the water level electrode inside the vessel. Also, ensure the door is fully closed, the door gasket is properly seated, and there is no steam leakage. Check the leveling of the machine.
How to fix ‘High Pres’ error on Tuttnauer 2340E?
If the 'High Pres' message appears on your Tuttnauer Laboratory Equipment, the air jet might be clogged; clean it. It could also mean that the heating elements are continuously on, or the temperature sensor is faulty. In these cases, contact a technician.
How to unclog the drain on Tuttnauer Laboratory Equipment?
If the drain of your Tuttnauer Laboratory Equipment is clogged: 1. Open the drain by turning it counterclockwise and place a heavy object over the reservoir cover. 2. Blow compressed air into the drain to force debris back into the reservoir, then clean out the reservoir. 3. Alternatively, disassemble the drain valve, clean it, and blow out the line. Reassemble the valve, ensuring the large 'O' ring is properly seated.
What should I do if my Tuttnauer 2340E displays ‘High Pres’?
If your Tuttnauer Laboratory Equipment displays ‘High Pres’, clean the air jet. Ensure the sterilization time and temperature are set correctly; if unsure, use the default settings. Also, make sure the autoclave is not too heavily loaded.
What to do if my Tuttnauer 2340E Laboratory Equipment is not responding?
If your Tuttnauer Laboratory Equipment is not responding, ensure the main switch is in the ‘On’ position. Also, verify the power cord is properly connected to both the machine and the mains. Check the reset button on the cut-out thermostat and make sure the circuit breaker hasn't tripped; lift the circuit breaker lever if it has.
Why is my Tuttnauer Laboratory Equipment leaking at the door?
If your Tuttnauer Laboratory Equipment is leaking at the door, ensure the door is tightened enough and the door gasket is sealing the chamber. If necessary, replace the door gasket.
Inspecting the autoclave for damage upon arrival and unpacking.
Details of the warranty coverage, limitations, and activation process.
Overview of autoclave purpose, standby mode, and environmental emissions.
Environmental requirements, power supply, construction materials, and symbol explanations.
Details on circuit breakers, fuses, and power ratings for various models.
Detailed physical dimensions of the autoclave models.
Comprehensive table of chamber, reservoir, weight, and shipping specifications.
Autoclave compliance with technical and quality standards, including FDA clearance.
Guidelines for acceptable physical and chemical characteristics of water for autoclave use.
Labeled diagrams of front panel components for different model series.
Visual differences between old (gray) and new (blue) control panel layouts.
Diagram identifying key components and connections on the rear of the autoclave.
Illustrations of old (gray) and new (blue) front panel keyboard layouts.
Explanation of the operational meaning of indicator lights on the control panel.
Description of program keys and parameter adjustment keys (TEMP, STE. TIME).
Explanation of keys for CLOCK, Water Inlet, START, and STOP functions.
Causes and solutions for 'Low Heat' and 'Low Pres' error messages.
Causes and solutions for 'Low Temp', 'High Temp', and 'Low Water' error messages.
Explanations for Door Unlock, High Pres, Man. Stop, Add Water, Power Dn, and Cycle Finish messages.
Details and nominal parameters for Unwrapped Instruments, Wrapped Instruments, and Glassware programs.
Specifics on settings and operation sequence for wrapped instruments and porous loads.
Details for Glassware program and the Accessory (Dry Only) program.
How the optional printer records cycle data, including software version and parameters.
Instructions for loading paper, performing tests, and handling the printer.
Guidelines for placement, load capacity, and safe electrical connection.
Steps for initial setup, including chamber pitch adjustment for different models.
Procedures for adjusting the automatic water fill level for various model ranges.
Safety guidelines for moving the autoclave and draining the water reservoir.
Procedures for loading, unloading, and filling the water reservoir with distilled water.
Steps for cleaning, rinsing, packaging, and preparing instruments for sterilization.
Verification of packaging, tray spacing, and optimal pack orientation in the chamber.
Addressing instrument spotting, discoloration, and preventing contact with chamber walls.
Steps for initial setup, program selection, and starting a sterilization cycle.
Details on drying stage, cycle completion, and important post-operation considerations.
Routine daily and weekly cleaning tasks for optimal autoclave performance.
Periodic maintenance activities including safety valve check and filter replacement.
Step-by-step guide for replacing the HEPA air filter on specific EA and EKA models.
Procedure for safely draining the autoclave's water reservoir.
Instructions for cleaning the air jet to ensure proper sterilization and prevent errors.
Procedure for removing and installing a new door gasket for proper sealing.
Monthly procedure to check the safety valve for blockages and ensure it functions correctly.
Instructions for safely replacing blown fuses and identifying correct fuse types.
Steps for cleaning the water outlet strainer, including important safety warnings.
Procedure for cleaning the autoclave using Chamber Brite cleaner for descaling.
Safety precautions and correct usage amounts for Chamber Brite cleaner.
Procedure for cleaning the water sensor to ensure accurate water level reporting.
Solutions for machine unresponsiveness and 'Low Heat' error messages.
Solutions for 'Low Water', 'Low Pres', and 'High Temp' error messages.
Solutions for printer malfunctions and door leaks.
Solutions for drain clogs, failed spore tests, and wet/burned wraps.
Addressing instrument rusting and slow autoclave heat-up times.
Troubleshooting for long drying times and chamber cleaning requirements.
General| Type | Autoclave |
|---|---|
| Heating Element | 1400W |
| Number of Trays | 2 |
| Frequency | 50/60Hz |
| Chamber Material | Stainless steel |
| Power Supply | 230V, 50/60Hz |
| Sterilization Cycle Time | 20-30 minutes |
| Standard Cassettes Capacity | 3 cassettes |
| Tray Dimensions | 6.7" x 16.3" x 0.8" |
| Power | 1.5 kW |
| Temperature Range | 105°C to 137°C |
| Power Consumption | 1.5 kW |
To Next Page
