Why are wraps burned after using Tuttnauer Laboratory Equipment?
To address wraps coming out burned from your Tuttnauer Laboratory Equipment, check if the water sensor is dirty. Also, verify that the wall outlet voltage is not too high and ensure items are not touching the chamber walls or bottom. Load the autoclave according to the instructions.
What to do when my Tuttnauer 2540EK displays ‘High Temp’?
If your Tuttnauer Laboratory Equipment displays ‘High Temp’, clean the air jet and check for proper voltage at the wall outlet.
What does ‘Low Heat’ mean on my Tuttnauer 2540EK?
If the message ‘Low Heat’ is displayed during heat up on your Tuttnauer Laboratory Equipment, it indicates a bad temperature sensor. If heating elements are remaining on instead of cycling on and off, call for a technician.
How to clean a very dirty chamber in my Tuttnauer 2540EK?
If the chamber of your Tuttnauer Laboratory Equipment is very dirty, use Chamber Brite ™ to clean the autoclave; very dirty machines may require two cleanings.
Why are instruments rusting in my Tuttnauer 2540EK Laboratory Equipment?
If instruments are rusting after sterilization in your Tuttnauer Laboratory Equipment, first determine if it's true rust by using a pencil eraser to remove the brown spot. If there is no pitting, the instrument is just dirty. Use distilled water for sterilizing and ensure dissimilar metals are not in contact with each other.
Why does Tuttnauer 2540EK printer feed paper constantly?
If the printer on your Tuttnauer Laboratory Equipment gives paper feeds all the time when the machine is switched on, make sure the ‘feed button’ on the printer is not stuck.
What to do if the keyboard of my Tuttnauer Laboratory Equipment does not respond?
If the keyboard of your Tuttnauer Laboratory Equipment does not respond, press the STOP key for 2 seconds to abort any program that may still be running.
How to troubleshoot a Tuttnauer 2540EK Laboratory Equipment system that shows no response when turned on?
If your Tuttnauer Laboratory Equipment does not respond when you turn it on, try the following: First, check and fix all connections. If the issue persists, replace any faulty cables, connectors, or the power switch.
Why is my Tuttnauer 2540EK making a loud noise?
If you hear a loud noise coming from the reservoir of your Tuttnauer Laboratory Equipment, the sterilization temperature may be set too high. The maximum setting is 274ºF (134ºC).
How to clean a very dirty Tuttnauer 2540EK Laboratory Equipment chamber?
To clean a very dirty chamber in your Tuttnauer Laboratory Equipment, use Chamber Brite ™. Very dirty machines may require two cleanings.
Inspect the autoclave's exterior and interior for damage upon arrival.
Details the two-year warranty for components and assembly, excluding wear items.
Presents electrical specifications, fuse types, and circuit breaker ratings.
Explanation of displayed messages and associated safety measures.
Program for sterilizing unwrapped instruments at high temperatures.
Program for sterilizing wrapped items and porous materials with drying.
Best practices for packaging instruments and loading the autoclave chamber.
Sequence for starting the autoclave for the first time, including water filling.
Daily, weekly, and periodic maintenance tasks for optimal autoclave performance.
Procedure to clean the air jet, critical for preventing sterilization test failures.
Monthly procedure to verify the safety valve is clear and functional.
Procedure for using Chamber Brite to clean and descale the autoclave.
Solutions for when the autoclave does not respond to commands.
Diagnosing and resolving 'Low Heat' or 'Low Temperature' errors.
Troubleshooting 'Low Water' messages, checking seals and leveling.
Resolving 'Low Pressure' or 'High Pressure' indications.
General| Type | Autoclave |
|---|---|
| Trays Capacity | 2 |
| Chamber Material | Stainless Steel |
| Chamber Dimensions | 10 in x 16 in |
| Warranty | 2 years |
| Temperature Range | 221°F to 273°F (105°C to 134°C) |
To Next Page
