Why are wraps burned after using Tuttnauer Laboratory Equipment?
To address wraps coming out burned from your Tuttnauer Laboratory Equipment, check if the water sensor is dirty. Also, verify that the wall outlet voltage is not too high and ensure items are not touching the chamber walls or bottom. Load the autoclave according to the instructions.
What to do when my Tuttnauer Laboratory Equipment displays ‘High Temp’?
If your Tuttnauer Laboratory Equipment displays ‘High Temp’, clean the air jet and check for proper voltage at the wall outlet.
What does ‘Low Heat’ mean on my Tuttnauer Laboratory Equipment?
If the message ‘Low Heat’ is displayed during heat up on your Tuttnauer Laboratory Equipment, it indicates a bad temperature sensor. If heating elements are remaining on instead of cycling on and off, call for a technician.
How to clean a very dirty chamber in my Tuttnauer 2540E Laboratory Equipment?
If the chamber of your Tuttnauer Laboratory Equipment is very dirty, use Chamber Brite ™ to clean the autoclave; very dirty machines may require two cleanings.
Why are instruments rusting in my Tuttnauer 2540E?
If instruments are rusting after sterilization in your Tuttnauer Laboratory Equipment, first determine if it's true rust by using a pencil eraser to remove the brown spot. If there is no pitting, the instrument is just dirty. Use distilled water for sterilizing and ensure dissimilar metals are not in contact with each other.
Why does Tuttnauer 2540E Laboratory Equipment printer feed paper constantly?
If the printer on your Tuttnauer Laboratory Equipment gives paper feeds all the time when the machine is switched on, make sure the ‘feed button’ on the printer is not stuck.
What to do if the keyboard of my Tuttnauer Laboratory Equipment does not respond?
If the keyboard of your Tuttnauer Laboratory Equipment does not respond, press the STOP key for 2 seconds to abort any program that may still be running.
How to troubleshoot a Tuttnauer Laboratory Equipment system that shows no response when turned on?
If your Tuttnauer Laboratory Equipment does not respond when you turn it on, try the following: First, check and fix all connections. If the issue persists, replace any faulty cables, connectors, or the power switch.
Why is my Tuttnauer 2540E making a loud noise?
If you hear a loud noise coming from the reservoir of your Tuttnauer Laboratory Equipment, the sterilization temperature may be set too high. The maximum setting is 274ºF (134ºC).
How to clean a very dirty Tuttnauer 2540E chamber?
To clean a very dirty chamber in your Tuttnauer Laboratory Equipment, use Chamber Brite ™. Very dirty machines may require two cleanings.
Inspecting the autoclave upon delivery for any signs of damage.
Provides detailed electrical specifications, including amp, watt, and fuse ratings.
Specifies the required physical and chemical characteristics of water for the autoclave.
Details the functions of each key on the control panel and program selection.
Explains error messages, warnings, and associated safety measures.
Covers electrical connection requirements, safety relays, and grounding.
Guidelines for loading, unloading, and safety during operation.
Instructions on how to properly fill the water reservoir with distilled water.
Steps for cleaning, rinsing, and preparing instruments before sterilization.
Steps for filling reservoir, connecting power, and selecting programs.
Instructions for loading material, closing the door, and starting the autoclave.
Outlines daily, weekly, and periodic maintenance tasks for the autoclave.
Procedure for cleaning the air jet to prevent sterilization failures.
Procedure for cleaning and descaling the autoclave using Chamber Brite.
Solutions for issues where the machine is unresponsive or displays 'Low Heat'.
Troubleshooting steps for 'Low Water' and 'Low Pres' error messages.
Solutions for 'Low Temp' and 'High Pres' error messages.
General| Model | 2540E |
|---|---|
| Number of Trays | 2 |
| Type | Autoclave |
| Power Supply | 230V, 50/60Hz |
| Power | 1700W |
| Current | 7.4A |
| Sterilization Pressure Range | 15-30 psi |
| Standard Cassettes Capacity | 2 |
| Standard Accessories | 1 tray |
| Cycle Time | Approximately 30 minutes |
| Heating Element | 1.5 kW |
| Power Consumption | 1.5 kW |
| Sterilization Temperature Range | 121°C - 134°C (250°F - 273°F) |
To Next Page
