To Next Page

To Previous Page

PowerSeries Pro Installation Guide

Trouble 03 – Bus Voltage:

[01] HSM2HOSTx Bus Low Voltage: The HSM2HOSTx module has measured a low

bus voltage.

[02] Keypad 01 - 16 Bus Low Voltage: A hardwired keypad has a low bus voltage.

[04] HSM2108 01 - 30 Bus Low Voltage: A zone expander has a low bus voltage.

[05] HSM2300 01 - 04 Bus Low Voltage: A power supply has a low bus voltage.

[06] HSM2204 01 - 04 Bus Low Voltage: A high current output module has a low

bus voltage.

[07] Bus Fault (System): Panel Corbus Output voltage is too hight or too low.

[08] HSM2208 01 - 16 Bus Low Voltage: The low current output module has detected

a low voltage.

[09] HSM2955 Bus Low Voltage: The audio module has detected a low bus voltage.

[10] HSM3408 Bus Low Voltage: The 8 zone expander has detected a low bus

voltage.

[11] HSM3204CX Bus Low Voltage: The corbus repeater has detected a low bus

voltage.

[12] HSM3204CX Bus Fault: The corbus repeater has detected that the corbus output

voltage is too high or too low.

[13] HSM3350 Bus Low Voltage: The 3 A power supply module has detected a low

bus voltage.

Trouble 04 – AC or DC input power trouble:

[01] Zone 001 - 248 AC or DC input power trouble.

[02] Keypad AC or DC input power trouble: A keypad has an AC or DC input power

trouble.

[03] Siren 01 - 16 AC: A siren has an AC or DC input power trouble.

[04] Repeater 01 - 08 AC: A wireless repeater has an AC or DC input power trouble.

[05] HSM2300 01 - 04 AC: An HSM2300 has an AC or DC input power trouble.

[06] HSM2204 01 - 04 AC: An HSM2204 has an AC or DC input power trouble.

[07] Panel AC: The alarm controller has an AC failure condition.

[08] HSM3204CX AC: A corbus repeater has an AC or DC input power trouble.

[09] HSM3350 AC: The 3A power supply has an AC or DC input power trouble.

Trouble 05 – Device Faults:

Note: Fire trouble is displayed directly under device faults when there is an open loop

condition for PGM-2 configured for 2-wire smoke.

[01] Zone 001 - 248: A zone is in supervisory fault.

[02] Keypad 01 - 16: A wireless or hardwired keypad is in supervisory fault.

[03] Siren 01 - 16: A siren is in supervisory fault.

[04] Repeater 01 - 08: A wireless repeater is in fault (supervisory or loss of AC/DC).

[06] Device Mask: A detection mechanism on the sensor is masked.

[07] Gas Trouble:A gas sensor is in fault.

[08] Heat Trouble: A temperature sensor is in fault or a temperature reaches the high

temperature warning threshold.

[09] CO Trouble: A CO sensor is in fault.

[10] Freeze Trouble: A temperature sensor falls below the low temperature warning

threshold.

[11] Probe Disconn.: The probe on the flood detector or the temperature detector is

disconnected.

[12] Fire Trouble: A smoke sensor is in fault.

Trouble 06 – Device Low Battery:

[01] Zone 001- 248: Wireless zone has a low battery.

[02] Keypad 01-16: Keypad has a low battery.

[03] Siren 01 - 16: Siren has a low battery.

[04] Repeater 01 - 08: Repeater has a low battery.

[05] User 01 - 1000: Wireless Key has a low battery.

Trouble 07 – Device Tampers:

[01] Zone 001 - 248 Tamper: A wireless or hardwired zone is in tamper.

[02] Siren 01 - 16 Tamper: A wireless siren is in tamper.

[03] Repeater 01 - 08 Tamper: A wireless repeater is in tamper.

[04] Audio Station 01 - 04 Tamper: An audio station connected to an HSM2955 is in

tamper.

Trouble 08 – RF Delinquency Trouble:

[01] Zone 001 - 248 RF Delinquency: No response from a wireless zone for 13

minutes. This trouble prevents arming until acknowledged or cleared using [*][2].

[02] Keypad 01 - 16 RF Delinquency: No response from a wireless keypad for 13

minutes.

[03] Siren 01 - 16 RF Delinquency: No response from a wireless siren for 13 minutes.

[04] Repeater 01 - 16 RF Delinquency: No response from a wireless repeater for 13

minutes.

Trouble 09 – Module Supervisory Trouble:

[01] HSM2HOSTx not responding.

[02] Keypad 01 - 16 not responding.

[04] HSM2108 01 - 30 not responding.

[05] HSM2300 01 - 04 not responding.

[06] HSM2204 01 - 04 not responding.

[08] HSM2208 01 - 16 not responding.

[09] HSM2955 is not responding.

[11] HSM3408 is not responding.

[12] HSM3204CX is not responding.

[13] HSM3350 is not responding.

Trouble 10 – Module Tamper:

[01] HSM2HOSTx Tamper.

[02] Keypad 01 - 16 Tamper.

[04] HSM2108 01 - 30 Tamper.

[05] HSM2300 01 - 04 Tamper.

[06] HSM2204 01 - 04 Tamper.

[08] HSM2208 01 - 16 Tamper.

[09] HSM2955 Tamper.

[10] Alt Comm Tamper.

[11] HSM3408 Tamper.

[12] HSM3204CX Tamper.

[13] HSM3350 Tamper.

Trouble 11 – Communications:

[01] TLM: Telephone line disconnected from control panel.

[02] Receiver 01-04 FTC Trouble: Failure to communicate using programmed receiver

paths.

[04] Alt. Comm Cellular: Radio or SIM card failure, low signal strength detected, or

cellular network fault.

[05] Alt. Comm Ethernet: Ethernet connection unavailable. A valid IP address is either

not programmed or the module was unable to get an IP with DHCP.

[06] Receiver 01-04 Trouble: Alternate communicator unable to initialize a receiver.

[07] Receiver 01-04 Supervision: Alternate communicator unable to communicate with

a receiver.

[09] Alt. Comm Fault: The alternate communicator has stopped responding.

[10] Alt Comm FTC Trouble: The alternate communicator has failed to communicate

an internal event not generated by the panel.

- 11 -

Series	Power Series
Category	Security System
System Type	Wired/Wireless Hybrid
Power Supply	AC with battery backup
Communication	IP
Remote Access	Mobile app, web portal
Alarm Type	fire, medical

Tyco Power Series User Manual

Table of Contents

Questions and Answers:

Tyco Power Series Specifications

Related product manuals