Vanatoo TRANSPARENT ZERO - ADJUSTING TREBLE AND BASS; Treble and Bass Adjustment; AUDIO MUSIC SOURCE PRECEDENCE; Automatic Input Switching Hierarchy

www.vanatoo.com 12
2. Ifyouareoutofrangeforaminuteorsothenwalkbackintorangethemobiledevice
mayautomaticallyreconnect(orjuststayconnected)butthemusicmaynotautomatically
beginagain.Allyouneedtodoishitplayonyourmobiledevice’smusicplayerandthe
musicwillresume.
3. Ifyouareoutofrangeformorethanaminutethenwalkbackintorangethemobile
devicewillmostlikelybedisconnectedfromtheT0whichwillrequireyoutoreconnectto
theT0’sBluetoothreceivertoplaymusicagain.
Theexactnatureofhowamobiledevicehandlesthe“outofBluetoothreceiverrange”issuevaries
fromdevicetodeviceandfromrevisiontorevision.Howeverthisisnotacomplexissueanditcan
alwaysberesolvedbyeitherrestartingthemusicorreconnectingtotheT0Bluetoothreceiveronce
thedeviceisbackintheBluetoothreceiver’srange.
ADJUSTING TREBLE AND BASS
ThetrebleandbasscanbeadjustedontheT0usingthevolumeknoblocatedonthetopof
theT0activespeakeralongwiththethreepositionV-T-B(volume/treble/bass)switchandthe
Pair/ProgbuttonbothlocatedonthebackoftheT0activespeaker.Tosetthetreblesetting,
startbyplayingsomemusic.WhilethemusicisplayingmovetheV-T-Bswitchtothe“treble”
position.Nowadjustthetreblesettingtotasteusingthevolumeknob(whichatthispointin
timeisredenedtobeatrebleknob).Notethatthetwodotsatthecenteroftheknob’stravel
denotesthe“at”position.Whenyouhavethetrebleadjustedtotastedepressandrelease
thePair/Progbutton.Thisactionlocksinthetreblesettingsoyoucanmoveontothebass
setting.TosetthebasssettingfollowthesameprocedureexceptwiththeV-T-Bswitchsetto
“bass.”WhenyouhavecompletedthetrebleandbasssettingsmovetheV-T-Bswitchtothe
volumepositionandthevolumeknobwillbecomeavolumeknobagain.
TIP
IfyouchangeabassortreblesettingbutforgettodepressthePair/Progbuttonthe
settingwillnotbesavedandthepreviouslysavedsettingwillbeused.
ADJUSTING THE BRIGHTNESS OF THE POWER ON LED
TheintensityofthebluepoweronLEDcanbeadjustedtotaste.Infactitcanbeturnedo
completelyifyouwant.ToadjusttheintensityoncetheT0sarepoweredupandtheblueLED
isonandnomusicisplaying,settheV-T-Bswitchtothe“volume”postition,holdthe“Pair/
Prog”buttondownfor5seconds.Afterthe5secondscontinuetoholdthebuttondown(do
notreleaseitoryouwillhavetostartthe5secondsoveragain).Thenrotatethevolumeknob
onthetopoftheT0activespeaker.WhenyouhavetheblueLEDintensitywhereyoulikeit
thenreleasethePair/Progbutton.That’sit.Nomoreneedofapieceofblackelectricaltape
stuckonthepoweronLEDtokeepyourbedroomdark.TheblueLEDwillnowbeatthis
intensityuntilyouchangeit(oruntilyoupowerotheT0).
TIP
WhenyouhavecompletedtheLEDintensityprocessbyreleasingthePair/Progbutton
remembertoreadjustyourvolumeknobtoyourdesiredlisteninglevel.Ifyouadjustyour
LEDintensitytoaverylowintensitythenforgettoreadjustyourvolumeknobwhenyou
aredoneyoumightwonderwhyyoucannolongerhearyourmusic.
AUDIO MUSIC SOURCE PRECEDENCE
IfyouhaveyourT0settoautoinputswitching(thisisthedefaultsetting)andmultipledevices
areconnectedtoyourT0speakers,thedeviceyouhearisautomaticallyselectedbasedon
thehierarchyshownbelow:
1. Analog
2. AudioUSB
3. OpticalS/PDIF
4. Bluetooth
Forexample,iftheT0isconnectedtoanMP3playerviathe3.5mmanalogconnectionand
toanetworkedaudiodeviceviatheTOSLINKopticalconnection,andbothareturnedon,the
MP3playeristhesourcethatwillbeplayed.Ifhowever,theMP3playeristurnedoandthe
networkedaudiodeviceislefton,thenetworkedaudiodevicewillbethesourcethatisplayed.
When switching from a higher priority input to a lower priority input, the higher priority
input must be OFF (or silent) for 7 seconds before the T0 amplier will switch to the
lower priority input. Thisenablestheampliertodiscernbetweenthehigherinputbeing
turnedoandnormalinter-tracksilencethusavoidingswitchingtothelowerpriorityinput
betweenaudiotracks.This7secondwaittimeisnotnecessarywhenswitchingfromasource
thatislowerinprioritytoonethatishigher.Therefore,switchingfromalowerpriorityinputto
ahigherpriorityinputwillhappenalmostimmediately.