Vanatoo TRANSPARENT ZERO User Manual

www.vanatoo.com 8
SPEAKER CONFIGURATION SETTINGS
Byusingthevolumeknob,thevolume/treble/bassselectorswitchandthePair/Progbuttoncertain
settingscanbechangedintheT0tomakeitoperatealittledierently.Thefeaturesthatcanbe
changedarelistedinthetablebelow.Toselectoneofthesesetupitemsyoumustrstpowero
theT0byunpluggingtheDCpowerplug,thensetthevolumeknobandthevolume/treble/bass
switchpertheselectionyouwishfromthetablebelow,thenwhileholdingthePair/Progbutton
downconnecttheDCpowerplug.FinallyreleasethePair/Progbuttonandthenewselectionis
lockedin.Notethatthedefaultsettingsarealsoshowninthetablebelow,soifallelsefailsyou
canrestoreallsettingstotheirdefaultselections.
AlsonotethatwhenasetupparameterhasbeenacceptedtheT0willashthepoweronblue
LEDaswellasthefrontamberLEDthreetimesassoonasthePair/Progbuttonisreleasedto
acknowledgetheparameterhasbeenset.InthecasethatT0isresettothefactorydefaultsthe
blueandamberLEDswillbeashedanumberoftimeswhichindicatecodedinformationabout
theT0.AfterthedefaultsetupiscompletethepoweronblueLEDwillremainonwhichindicates
thefactorydefaultsaresetandtheT0isreadytoplaymusic.Allofspeakercongurationsettings
arenon-volatilewhichmeanstheywillremainevenifyoupowerotheT0.
TIP
WhenyouhavecompletedthespeakercongurationsettingsbesuretosettheV-T-Bswitchto“volume”andsetthevolume
knobtoatleastthemidwayposition(twodots)otherwiseyoumaytrytoplaymusicandnotrealizethatthevolumeisturnedall
thewaydown.
Default
Setting
Setting Volume Knob Three Position Slider Switch
Resetsettingstofactorydefaults Onedotposition(Min) Volume
X Enablessleepmodeafter20minutes Onedotposition(Min) Treble
Disablessleepmode—neversleeps Onedotposition(Min) Bass
X Remote“Enable”keymustprecederemoteBTPair,
Treble,andBasschanges
Twodotposition(Mid) Volume
Remote"Enable"keymustprecederemoteinput
selection,BTPair,TrebleandBasschanges
Twodotposition(Mid) Treble
X EnablesshelvedDSPsettings Twodotposition(Mid) Bass
EnablesatDSPsettings Threedotposition(Max) Volume
X Stereooutput Threedotposition(Max) Treble
Monooutput Threedotposition(Max) Bass
X ResettoAutoInputSwitchmodeinsleep Halfwaybetweenonedotandtwodots Volume
Retaincurrentinputselectioninsleep Halfwaybetweenonedotandtwodots Treble
X Limitersenabled Halfwaybetweenonedotandtwodots Bass
Limitersdisabled Halfwaybetweentwodotsandthree Volume
X Activespeakerontheright Halfwaybetweentwodotsandthree Treble
Activespeakerontheleft Halfwaybetweentwodotsandthree Bass
(continued next page)

Vanatoo TRANSPARENT ZERO Specifications

General

Type	Powered Bookshelf Speakers
Configuration	2-way
Outputs	Subwoofer output
Inputs	USB, Optical, Analog 3.5mm
Weight	6.5 lbs per speaker
Tweeter	1 inch natural silk dome