VAT 61232-KEGJ-0002 User Manual (English)

Questions and Answers:

V
Virginia GallegosAug 27, 2025
What does error E21 mean on VAT 61232-KEGJ-0002 display?
- C
  Christopher AcostaAug 27, 2025
  If your VAT Control Unit displays 'E 21' and the position '009999' (fatal error - rotation angle of valve plate limited during power up), check if the valve plate is centric adjusted, if the valve unit is heavily contaminated or if the valve plate is mechanically obstructed. Adjust the valve plate according to the maintenance procedure, clean the valve unit, and resolve any obstructions. Reset the control unit by cycling the power off and on, or send a reset command locally via the service port with CV/CPA/Service Box2.
M
mendezkevinSep 10, 2025
Why does ZERO not work on my VAT 61232-KEGJ-0002?
- C
  codygonzalezSep 10, 2025
  If the VAT Control Unit ZERO does not work, OPEN the VALVE and bring the chamber to base pressure before performing ZERO. If ZERO is disabled, enable it, referring to «Valve configuration» for details.
S
Sandra AdkinsAug 27, 2025
What does error E20 mean on VAT 61232-KEGJ-0002 display?
- M
  Michael DavisAug 27, 2025
  If the VAT Control Unit display shows 'E 20' and position '009999' (fatal error - limit stop of valve unit not detected), ensure the clamp coupling screw is tightened. Refer to the maintenance chapter for detailed instructions. A RESET or restart of the valve is then necessary.
K
Kimberly RobinsonAug 27, 2025
What does D 0 mean on VAT Control Unit display?
- D
  David JenkinsAug 28, 2025
  If the VAT Control Unit display shows 'D 0' indicating the Motor Interlock is open, ensure that power is supplied to the motor to allow for operation. Refer to the electrical connection details for guidance.
D
Drew JenkinsAug 28, 2025
What does error E40 mean on VAT 61232-KEGJ-0002 display?
- P
  Paul GonzalezAug 28, 2025
  If the VAT Control Unit displays 'E 40' and position '009999' (fatal error - motor driver failure detected), replace the control and actuating unit according to the maintenance procedure.
W
Wanda AdamsSep 12, 2025
What to do if my VAT 61232-KEGJ-0002's Network Status LED is flashing red (time out)?
- S
  Savannah ThompsonSep 13, 2025
  If the Network Status LED is flashing red, it indicates a time-out. Reestablish I/O connections to resolve this issue.
G
George VasquezSep 8, 2025
Why does my VAT 61232-KEGJ-0002 Control Unit display «E 21» error?
- A
  Adam FranklinSep 8, 2025
  If the VAT Control Unit display shows «E 21» because the valve plate is not centric adjusted, adjust the valve plate according to «Maintenance procedure». If the valve unit is heavily contaminated, clean it according to « Maintenance procedure ». If the valve plate is mechanically obstructed, resolve the obstruction. Alternatively, reset the control unit by cycling the power (OFF then ON) or send a reset command locally via the service port with CV/CPA/Service Box2.
S
Sarah BrownSep 6, 2025
What to do if VAT 61232-KEGJ-0002 display shows «E 22»?
- M
  Mary CooleySep 6, 2025
  If the display shows «E 22» on your VAT Control Unit, indicating a fatal error with the rotation angle of the valve plate during operation, consider these solutions: * The valve unit may be heavily contaminated, so clean it according to the « Maintenance procedure ». * The valve plate might be mechanically obstructed; resolve the obstruction.
A
Amanda WoodAug 29, 2025
Why PRESSURE CONTROL does not work on VAT 61232-KEGJ-0002?
- K
  Kimberly RodriguezAug 29, 2025
  To resolve the issue of PRESSURE CONTROL not working on your VAT Control Unit, ensure that power is supplied to the motor. Select PRESSURE CONTROL mode and perform LEARN. The problem may be due to safety mode being active, PRESSURE CONTROL not being selected, or LEARN not being completed.
A
Alex WilliamsAug 29, 2025
How to fix «E 20» error on VAT 61232-KEGJ-0002 Control Unit?
- R
  robertporterAug 29, 2025
  To address the 'E 20' error on your VAT Control Unit, where the limit stop of the valve unit is not detected, tighten the clamp coupling screw. Then, reset or restart the valve. The error is caused by a clamp coupling screw that is not fastened.