To Next PageTo Next Page
Need help?Do you have a question about the VENOM VR3T and is the answer not in the manual?
General| Brand | VENOM |
|---|---|
| Model | VR3T |
| Category | Transmitter |
| Language | English |
Details the function and use of the navigation keys on the transmitter.
Outlines essential steps for setting up and operating the VR3T 2.4 transmitter, including connections and power-on sequence.
Explains how to use the steering trim for fine adjustments and centering the steering servo.
Describes the use of the throttle trim for adjustments and centering the throttle servo.
Details the information presented on the main screen, including battery voltage and model settings.
Instructions on how to access the programming mode from the main screen using the ENTER button.
Explains End Point Adjustment (EPA) for setting maximum travel of functions from 0-120%.
Provides step-by-step instructions for setting EPA values using the transmitter controls.
Describes Steering Dual Rate (ST D/R) for creating two steering travel presets for driving adjustments.
Guides users through setting ST D/R values, selecting presets, and changing values using transmitter buttons.
Explains Sub Trim for 1% incremental adjustments to center servos during assembly or driving.
Details the process of selecting and adjusting Sub Trim values for steering and throttle servos.
Explains the Reverse function for changing the direction of movement for servos or speed controls.
Provides steps to access and change the Reverse setting for steering, throttle, and auxiliary channels.
Describes Steering Curve for adjusting steering servo sensitivity around neutral without changing maximum travel.
Guides users on setting the Steering Curve adjustment range and using buttons for faster or slower steering.
Explains Throttle Curve for changing throttle and brake response with EXP, VTR, and CUR types.
Details the EXP curve for smoothing throttle response and adjusting brake aggressiveness.
Describes the CUR curve, allowing adjustments to three throttle rate points and braking rate.
Explains the VTR curve for adjusting throttle response speed in specific ranges via switching points.
Details the ABS feature that pulses brakes to reduce skidding or under steer.
Explains ABS parameters like PT, WD, CY, DL, SM, DT, and MODE for adjusting brake behavior.
Guides users through setting ABS values for trigger point, return amount, cycle speed, delay, mix, duty, and mode.
Covers selecting, editing, and copying model profiles for up to 16 models.
Explains how to set steering speed, including turning and return speed for the steering servo.
Explains the Automatic Start (ATS) feature for smooth acceleration on slippery tracks by adjusting throttle servo position.
Details ATS parameters: Throttle Trigger Position (TRI), Preset Position (POS), Delay (DLY), and Mode (MOD).
Step-by-step guide on binding the VR3T transmitter to a 3 Ch 2.4ghz receiver using the MODULATE function.
Explains mixing a secondary braking system from the AUX channel with the throttle channel.
Guides on setting the BRAKE MIX rate and enabling the feature for controlling rear brakes.
Describes mixing functions for greater control of the model, allowing adjustments to steering and throttle.
Explains Throttle Hold as an alternative to choke for starting motors, locking throttle until button press.
Details how to enable and release Throttle Hold while running the model for starting or warm-up procedures.
Explains the Fail Safe feature to prevent loss of control by setting preset values for steering or throttle on signal loss.
Guides on setting Fail Safe values for steering and throttle, enabling the feature, and setting INH or ON/OFF.
Describes calibrating the neutral center point for the steering wheel or throttle trigger.
Provides steps to set YES for neutral calibration and emphasizes not moving controls during the process.
Explains how to turn the beeping tones ON or OFF on the transmitter.
Details resetting the entire VR3T 2.4 transmitter memory to factory default settings.
Explains resetting a specific model memory slot back to factory default settings.
Describes using the timer to monitor race, lap times, or test sessions, with UP_T and DN_T modes.
Details setting timer increments, maximum limits, and how the timer starts and stops.
Lists technical specifications for the VR3T 2.4 GHz Transmitter, including part numbers and power requirements.
Details the specifications of the Venom 2.4GHz 3 Channel Receiver, including channel assignments.
Explains the function of the ENTER, EXIT, and +/- keys for navigating and selecting options in the menus.
Details FCC compliance, potential interference, and warnings regarding modifications.
Outlines the warranty terms, defect coverage, and contact information for customer service.
States copyright information and conditions for reprinting or excerpting manual content.
Disclaims liability for warranty and notes that product may vary from shown or is subject to change.
Provides a warning about chemicals in the product known to cause cancer and other reproductive harm.
