To Next PageTo Next Page
Need help?Do you have a question about the Vibe 7 Series and is the answer not in the manual?
General advice and warnings regarding amplifier installation and operation.
Cautionary advice regarding amplifier heat generation during normal use.
Lists specific conditions and actions that void the product warranty.
Information on obtaining warranty service outside the country of purchase.
Alerts users to the risk of hearing damage from high sound pressure levels.
Details on how to correctly connect the amplifier's power supply.
Explains connecting audio sources using RCA cables.
Describes connecting audio sources via speaker-level outputs.
Matches input signal to source for optimal amplifier performance.
Adjusts bass frequency boost, variable from 0dB to +12dB.
Selects frequency for bass boost, adjustable between 30Hz and 80Hz.
Selects multiplier for High Pass Filter frequency (x1 or x10).
Sets crossover frequency for HPF, adjustable based on multiplier.
Selects multiplier for Low Pass Filter frequency (x1 or x10).
Sets crossover frequency for LPF, adjustable based on multiplier.
Selects amplifier crossover mode: FLAT, HPF, or LPF.
Adjusts output phase between 0° and 180° for speaker alignment.
Connection for audio sources with low-level output via RCA.
Connection for audio sources using speaker-level outputs.
Port for connecting a supplied remote level control accessory.
Connects speaker cables to the amplifier for audio output.
Indicates amplifier status: Green for normal, Red for protection.
Connects DC power to the amplifier for operation.
Matches input signal for channels 3 and 4 to the source.
Adds bass boost for channels 3/4, variable 0dB to +12dB at 45Hz.
Alters output phase for channels 3/4 between 0° and 180°.
Limits very low frequencies for channels 3/4 (15Hz-40Hz).
Sets crossover frequency for channels 3/4 when LPF is selected.
Selects multiplier for LPF frequency (x1 or x10) for channels 3/4.
Turns LPF on or off for channels 3 and 4.
Turns HPF on or off for channels 3 and 4.
Selects multiplier for HPF frequency (x1 or x10) for channels 3/4.
Sets crossover frequency for channels 3/4 when HPF is selected.
Matches input signal for channels 1 and 2 to the source.
Sets crossover frequency for channels 1/2 when LPF is selected.
Selects multiplier for LPF frequency (x1 or x10) for channels 1/2.
Turns LPF on or off for channels 1 and 2.
Turns HPF on or off for channels 1 and 2.
Selects multiplier for HPF frequency (x1 or x10) for channels 1/2.
Sets crossover frequency for channels 1/2 when HPF is selected.
Connection for audio sources with low-level output via RCA.
Connection for audio sources using speaker-level outputs.
Port for connecting remote level control for channels 3 and 4.
Connects speaker cables to the amplifier for audio output.
Indicates amplifier status: Green for normal, Red for protection.
Specifies fuse type and rating for replacement: 3 x 25A.
Connects DC power to the amplifier for operation.
Matches input signal for channels 1 and 2 to the source.
Sets crossover frequency for channels 1/2 when HPF is selected.
Selects multiplier for HPF frequency (x1 or x10) for channels 1/2.
Turns HPF on or off for channels 1 and 2.
Sets crossover frequency for channels 1/2 when LPF is selected.
Selects multiplier for LPF frequency (x1 or x10) for channels 1/2.
Turns LPF on or off for channels 1 and 2.
Matches input signal for channels 3 and 4 to the source.
Sets crossover frequency for channels 3/4 when HPF is selected.
Selects multiplier for HPF frequency (x1 or x10) for channels 3/4.
Turns HPF on or off for channels 3 and 4.
Sets crossover frequency for channels 3/4 when LPF is selected.
Selects multiplier for LPF frequency (x1 or x10) for channels 3/4.
Turns LPF on or off for channels 3 and 4.
Sets input mode for the amplifier: 2, 4, or 6 channel.
Matches input signal for channels 5 and 6 to the source.
Adds bass boost for channels 5/6, variable 0dB to +12dB at 45Hz.
Limits very low frequencies for channels 5/6 (15Hz-40Hz).
Sets crossover frequency for channels 5/6 when HPF is selected.
Turns HPF on or off for channels 5 and 6.
Sets crossover frequency for channels 5/6 when LPF is selected.
Turns LPF on or off for channels 5 and 6.
Alters output phase for channels 5/6 between 0° and 180°.
Connection for audio sources using speaker-level outputs.
Connects speaker cables to the amplifier for audio output.
Indicates amplifier status: Green for normal, Red for protection.
Specifies fuse type and rating for replacement: 4 x 25A.
Connects DC power to the amplifier for operation.
Step-by-step guide to correctly set the amplifier's gain control.
Recommendations for setting crossovers based on speaker type.
General
