VTech t 2453 - Telephone Memory; Store a Number;Name in Memory; Edit a Number;Name Stored in Memory; Delete a Number;Name Stored in Memory

14
15
Basic Operation Basic Operation
Speed Dialing
Telephone Memory
1 1
2 A B C 2
3 D E F 3
4 G H I 4
5 J K L 5
6 MNO6
7 PQRS7
8 T U V 8
9 W X Y Z 9
0 0
* *
# & ’ ,-.#
Presses
Dial Key 1 2 3 4 5 6
You can store up to nine numbers with names (up to 15 characters and 24 digits in each location)
you dial frequently into the speed dial memory locations you assign (1 through 9) in each handset.
You can also store telephone numbers with names alphabetically in the directory. See Telephone
Directory for instructions.
NOTES:
• The entries you stored in speed dial memory will be marked with 01 through 09 in the telephone
directory.
• Press OFF at any time to exit memory dial mode.
Store a Number/Name in Memory:
1. Press PROG on the handset.
2. Press or until the screen displays SPEED DIAL.
3. Press SEL. The screen displays ENTER 1-9.
NOTE: When memory is full the screen displays MEMORY FULL, an error tone sounds,
and you cannot store a new number until you delete a record in speed dial memory or
telephone directory.
4. Press the key (1 through 9) for the memory location where you want to store this
entry.If the selected location is empty, the screen displays ENTER NAME.
NOTE: If the location is not empty, your new entry will be stored in place of the old and the
first entry will be deleted. Take caution to not save over entries you do not wish to delete
from memory.
5. Using the chart below, enter up to 15 characters for the name you’re storing with the
number. Use to backspace and make corrections; use to advance and add
a space.
6. When you finish entering the name, press SELECT or PROG. The screen displays
ENTER NUMBER.
7. Enter the telephone number. Use to backspace and make corrections. Press
REDIAL/PAUSE to store a pause in the dialing sequence.
-OR-
Press REDIAL/PAUSE to display the last number dialed from this phone.
8. Press SELECT or PROG to store your entry. The screen displays DISTINCT
RING?and the current setting.
9. Press or to change the setting. Choose Y (for yes) if you wish the phone to alert
you to calls from this number by changing to a distinctive ringing pattern after the
first ring. Choose N for a normal ringing pattern.
10. Press SELECT or PROG to confirm your selection. If you chose Y, a D will be
displayed with the directory entry.
Edit a Number/Name Stored in Memory
1. Press and hold the memory location key (1 through 9) of the entry you wish to edit.
2. When the screen displays the entry you want to edit, press SELECT. Then press
or until EDIT flashes.
3. Press SELECT. The screen displays the name and number. The cursor appears at
the end of the name. Use , and the dial pad keys to edit the name. Press
SELECT to move on to edit the number. Use to backspace and make corrections.
PressSELECT to move to edit the distinctive ring setting.
4. Press SELECT to save.
Delete a Number/Name Stored in Memory
1. Press and hold the memory location key (1 through 9) of the entry you wish to delete.
2. When the screen displays the entry you want to delete, press SELECT. Then press
or until ERASE flashes.
3. Press SELECT. The screen displays ERASE NO YES and the number.
4. Press or until YES flashes.
5. Press SELECT. You’ll hear a confirmation beep.
Dial a Memory Number
1. Press and hold the memory location key (1 through 9) of the entry you wish to dial.
2. Press PHONE to dial the displayed memory number.
SPEED EDIT ERASESPEED EDIT ERASE
SPEED EDIT ERASESPEED EDIT ERASE
SPEED EDIT ERASE
80059595118005959511
80059595118005959511
8005959511
01
SPEED EDIT ERASESPEED EDIT ERASE
SPEED EDIT ERASESPEED EDIT ERASE
SPEED EDIT ERASE
80059595118005959511
80059595118005959511
8005959511
01