VTech VC7151-102A - Page 32

85 pages

Save Page as PDF

To Next Page

To Previous Page

Mount the sensor unit

Without Spacer

Mount with tape

1. Attach the mounting tape B onto

the rectangular area at the rear

side of the back cover

2. Stick the sensor unit onto the

frame.

Main Page

Default Chapter2
- Important Safety Instructions2
- Save These Instructions3
- About Cordless Telephones4
- Table of Contents5
Introduction7
What's in the Box8
Overview11
- Handset Overview11
- Telephone Base Overview14
- Contact Sensor Overview18
- Sensor Unit Overview18
- Display Icons Overview19
- Lights Overview21
Installation Setup22
- Telephone Installation22
  - Install the Handset Battery23
  - Charge the Handset Battery23
Sensor Battery26
- Contact Sensor Installation27
Before Use34
- Set Date and Time34
- Check for Dial Tone34
- Operating Range34
Sensor35
- Arm/Disarm the Sensor Alert System36
- Sensor Mode37
- Edit Numbers for Remote Calls38
- Set Time Delay for Remote Calls38
- Access an Individual Sensor Menu40
- Set Alert Schedule as Always on41
- Set a Time Range for Alerts42
- Turn off the Alerts43
- Alert Notifications44
- Test Sensor Signal Strength45
- Rename the Sensor46
- Reset Sensor Alerts46
- Sensor Log47
Configure Your Telephone48
- Using the Menus48
- Set Voice Langauge48
- Set Date and Time48
- Quiet Mode49
- Synchronize the Date & Time with Calling Number Display Service49
- Dial Mode49
Telephone Operations50
- Make a Call50
- Answer a Call50
- End a Call50
- Handset Speakerphone50
- Volume50
- Mute51
- Call Waiting51
- Chain Dialing51
- Access a Number in the Phonebook While on a Call51
- Access a Number in the Caller ID Log While on a Call51
- Equalizer52
- Find Handset52
- Redial List52
- Save a Redial Entry to the Phonebook53
- Join a Call in Progress53
- One-Touch Broadcast (OTB)53
- Switch an OTB Communication to the Intercom Call54
- Turn the OTB Call on or off54
- Intercom54
- Share Call55
- Transfer a Call55
- Answer an Incoming Call During an Intercom Call55
Phonebook56
- Add a Phonebook Entry56
- Review and Dial from the Phonebook57
- Edit a Phonebook Entry57
- Delete a Phonebook Entry57
Caller ID58
- Caller ID Log58
- Review and Dial a Number in the Caller ID Log58
- Save a Caller ID Log Entry to the Phonebook58
- Delete a Caller ID Log Entry58
- Delete All Caller ID Log Entries59
Call Block60
- Block Unknown Calls60
- Add a Call Block List Entry60
- Review the Call Block List61
- Edit a Call Block List Entry61
- Save a Caller ID Log Entry to Call Block List61
- Delete a Call Block List Entry61
Sound Settings62
- Key Tone62
- Ringer Tone62
- Ringer Volume62
- Temporary Ringer Silencing63
About the Built-In Answering System and Voicemail Service64
Set Your Built-In Answering System65
- Turn the Answering System on or off65
- Default Announcement65
- Record Your Own Announcement66
- Play the Announcement66
- Reset the Announcement66
- Set Number of Rings67
- Message Alert Tone67
- Recording Time68
Use Your Built-In Answering System69
- New Message Indication69
- Message Playback69
- Delete All Old Messages70
- Call Intercept70
- Call Screening70
Remote Access71
- Listen to Messages from Remote Access71
- Change Sensor Mode from Remote Access72
- Remote Access Code72
Use the Built-In Answering System and Voicemail Service73
Retrieve Voicemail from Telephone Service73
- Retrieve Voicemail73
- Set Your Voicemail Number73
- Turn off the New Voicemail Indicators74
Add a New Handset75
Add a New Sensor76
Deregister the Sensor77
ECO Mode78
General Product Care78
Storage79
Frequently Asked Questions80
Technical Specifications83
Disclaimer84

VTech VC7151-102A - Page 32

Table of Contents

Related product manuals