To Next Page
P
Pamela HernandezSep 10, 2025
Why does my WaterBoss 950 Water Dispenser indicate flow when no water is being used?
- MMatthew MccoySep 12, 2025
This usually means the household plumbing system has a leak. Repair the leak to resolve the issue.
Why does my WaterBoss 950 Water Dispenser indicate flow when no water is being used?
This usually means the household plumbing system has a leak. Repair the leak to resolve the issue.
Why is my WaterBoss Water Dispenser dispensing salty water?
Several factors can lead to salty water. Here's what to check: * Plugged injector: Replace the injector screen, nozzle, and throat. * Low water pressure: Maintain a minimum pressure of 20 psi. * Restricted drain line or flow control: Remove any restrictions. * Restricted or crimped brine line: Remove any restrictions; replace the line if crimped. * Excessive water in brine cabinet: Verify the correct water level relative to the salt setting and check lines and fittings for loose connections. * Intermittent pressure drop: Install a check valve on the inlet water line to the appliance (check local plumbing codes first). * Brine valve drips water back to brine cabinet: Clean the brine valve housing and replace the piston assembly.
Why is there no read-out in the display of my WaterBoss 950 Water Dispenser?
Check the following: * Make sure the electric cord is plugged in. * Verify there is electric power at the outlet and ensure the outlet is not controlled by a switch. * Test the transformer with a volt meter for 12 VAC at the control. If it's less than 10 VAC or greater than 14 VAC, replace the transformer. * With 12 VAC present at the controller, replace the controller if there's still no display. * Note that high ambient room temperature can cause this, but no action is necessary.
General| Type | Water Softener |
|---|---|
| Capacity | 31, 000 grains |
| Dimensions | 14.75" D x 18.75" W x 47.75" H |
| Weight | 118 lbs |
| Flow Rate | 12 gpm |
| Salt Storage Capacity | 250 lbs |
| Power Source | Electric |
Defines the original owner and location for warranty coverage.
Outlines what the limited warranty covers, including workmanship and materials.
Specifies repair/replacement terms for parts and tanks over 3 and 10 years.
Lists conditions and damages not covered by the warranty instrument.
Details how to report defects and contact WaterBoss for warranty claims.
Section for recording installation date, model, serial number, and water test results.
Provides rated efficiency data for models 700, 900, and 950 at specified conditions.
Ensures water supply meets necessary standards for appliance operation.
Identifies iron types and how they affect water softener performance.
Specifies pH and iron testing requirements for optimal performance.
Details maximum hardness levels the appliance can condition for each model.
Defines minimum and maximum water pressure for proper operation.
Specifies minimum flow rates required for appliance function.
Key steps to follow during installation, including codes and placement.
Critical actions to avoid during installation to prevent damage or malfunction.
Ensuring a clean, accessible, and properly situated location for the appliance.
Using test strips or lab analysis to determine water properties before setting.
Safely shutting off water and depressurizing lines before connecting.
Attaching inlet and outlet water lines to the appliance using proper fittings.
Installing the overflow line to a suitable drain for excess water.
Routing the backwash water drain line to a waste receptor.
Purging plumbing of air and foreign materials after initial connections.
Inspecting all connections for water leaks after filling the system.
Connecting the power supply to the controller unit.
Initial programming of the appliance's control unit.
Adding the initial water volume to the brine tank.
Adding salt to the brine tank for water softening.
Final checks, power-on, and flushing to meet NSF requirements.
Isolating the appliance for maintenance or using untreated water.
Adjusting the bypass valve to reintroduce hardness into the water.
Description of the controller's screen elements and status indicators.
Explains how the controller measures usage for regeneration.
Shows the amount of soft water left until the next regeneration.
Details cycle numbers during the regeneration process.
Indicates water flow through the appliance for leak checks.
Shows when the PowerClean maintenance feature is active.
Used to initiate customer settings or enter advanced modes.
Used to modify settings or cycle through options.
How to use the Power Clean feature for iron-heavy water.
Steps to manually start a regeneration cycle.
Method to step through regeneration cycles for setup or diagnosis.
Steps to measure water hardness and pH for controller setup.
Inputting the determined hardness setting into the controller.
Configuring the appliance for High Capacity (HC) or High Efficiency (HE) modes.
Choosing between Delay or Demand regeneration modes.
Configuring automatic regeneration frequency.
Selecting the unit of measurement for water volume.
Choosing between 12-hour (AM/PM) or 24-hour clock display.
Setting the current time on the controller.
Programming the desired time for automatic regeneration.
Guidelines for connecting copper pipes to the bypass valve assembly.
Instructions for solvent cementing PVC/CPVC pipes for secure joints.
Diagram and list of parts for the main housing and lids.
Diagram showing various cabinet and connected assemblies.
Components and function of the injector assembly for brine solution.
Components and function of the bypass valve assembly.
Parts and installation for the fill plug on the Model 950.
Components and diagram of the drive end cap assembly.
Description of the drive motor and its connection.
Description of the drive gear and its role in torque transfer.
Description of the cover securing the piston slide cam.
Description of the piston slide cam, the heart of the drive system.
Details on the drive end cap, its seals, and assembly.
Description of the piston slide and its movement within the housing.
How to attach and detach the drive piston to the piston slide.
Components and function of the brine valve housing.
Components and diagram of the safety shutoff mechanism.
Instructions for connecting the safety shutoff valve elbow.
Diagnosing and fixing issues with soft water output post-regeneration.
Common causes and solutions for lack of soft water production.
Troubleshooting reasons for the waterMizer indicator not showing flow.
Addressing false flow indications or leaks detected by waterMizer.
Resolving issues with the controller display not showing information.
Troubleshooting why the unit is stuck in a regeneration cycle.
Identifying causes for too much water in the brine cabinet.
Fixing issues where regeneration cycles are not completing correctly.
Diagnosing and resolving issues causing salty or hard water output.
Interpreting and resolving specific error codes displayed by the controller.
Detailed technical specifications for the WaterBoss 700 model.
Detailed technical specifications for the WaterBoss 900 model.
Detailed technical specifications for the WaterBoss 950 model.
Copies of state certifications for water treatment device performance.
