Why my Whirlpool Control Panel will not shut off?
If your Whirlpool Control Panel won't shut off when expected, check the lint screen and exhaust vent for poor airflow, and clean if necessary. Also, perform Key Activation & Encoder Test for the Start/Pause button.
Why my Whirlpool Control Panel will not power up?
If your Whirlpool Control Panel isn't powering up, with no keypad response or LED display, first check the power at the outlet, circuit breaker, fuses, and junction box connections. It may be due to no power to the dryer.
Why is my Whirlpool Washer vibrating, rocking, or “walking”?
Your Whirlpool Washer might be vibrating, rocking, or “walking” due to several reasons: * The feet may not be in contact with the floor and locked, so ensure the front and rear feet are in firm contact with the floor, and the washer is level. * The washer may not be level. Inspect the floor for flexing or sagging. If the flooring is uneven, placing a 3/4" (19 mm) piece of plywood under the washer can help reduce the sound.
What to do if my Whirlpool Washer is not draining or spinning properly?
If your Whirlpool Washer isn't draining or spinning and loads are still wet, first, empty pockets and use garment bags for small items. Cycles with lower spin speeds remove less water than cycles with high spin speeds, so use the recommended cycle/speed spin for your item. Tightly packed loads may not allow the washer to spin correctly; evenly arrange the wet load for balanced spinning and select RINSE & SPIN to remove excess water. Check the drain hose for proper installation, ensuring it doesn't extend into the standpipe farther than 4.5" (114 mm). Securely attach it to the drainpipe or tub, and do not tape over the drain opening. Lower the drain hose if the end is higher than 96" (2.4 m) above the floor. Remove any clogs from the drain hose.
How to stop my Whirlpool cabrio Washer from vibrating?
To address vibration, rocking, or “walking” in your Whirlpool Washer, ensure the front and rear feet are firmly in contact with the floor, and the washer is level. Tighten the jam nuts against the bottom of the cabinet. If the flooring is uneven, placing a 3/4" (19 mm) piece of plywood under the washer may help reduce noise.
What to do if the error code appears and the Whirlpool cabrio Washer has stopped?
If the dial is flashing and the washer has stopped, redistribute the load, close the lid, and press START/PAUSE. Allow the washer to continue the load-balance correction routine.
What to do if the Whirlpool Washer displays an error code due to a large load?
If an overload is detected, the Whirlpool Washer will drain any water and detergent. Remove several items, add HE detergent, close the lid, and press START/PAUSE.
Why does my Whirlpool cabrio keep stopping?
To resolve a Whirlpool Washer stopping mid-cycle, ensure the power cord is plugged into a grounded 3-prong outlet and that there is power to the outlet. Avoid using an extension cord. Also, the lid must be closed for the washer to run. Remember, the washer will pause during certain phases of the cycle, so avoid interrupting it.
What to do if Whirlpool Control Panel will not start cycle?
If your Whirlpool Control Panel isn't starting when you press the Start button, make sure the door is completely closed. Then, press and hold the START button.
What to do if my Whirlpool cabrio displays a PF (power failure) error?
To address a PF (power failure) error on your Whirlpool Washer, touch START to continue the cycle or touch POWER to clear the display. This usually happens if a power failure occurred while the washer was running.
Guidelines for voltage measurements, ESD protection, and technician safety notices.
Visual guides to Whirlpool, Maytag, and Kenmore control panels.
Activating diagnostic modes, tests, software versions, and error code references.
Common problems, causes, component testing, diagrams, and locations.
General| Wash Cycles | 12 |
|---|---|
| Energy Star Certified | Yes |
| Color | White |
| Steam Function | Yes |
| Type | Top Load |
To Next Page
