EasyManua.ls Logo

widos 5100 - Page 26

widos 5100
51 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
Kunststoffschweißtechnik
Foundation: 2207, 2208 DIN 16932 German association for welding
Use for:
5100
OD 200 - 450
5500
OD 200 - 500
1 bar on manometer:
141
N
PE 80
The value for heating element temperature is between 200° C - 220° C.
The
smaller
the pipe wall the
higher
the temperature.
PE 100
The standard value for heating element temperature is 220° C.
Increase the change-over time and the welding pressure time at PE 100 as fast as possible !
time to
change- reach full
over welding cool-down time
0,15 (PE) time pressure
pressure in
T
desired
temperature
time
pipe
pipe
SDR
bead-up
circular
heat-up
max.
time
welding
cool-
diameter
wall
pressure
bead
time
change-
to reach
pressure
down
OD
(s)
[bar]
min.
[s]
over
welding
[bar]
time
[mm]
[mm]
[mm]
time
pressure
[min]
[s] [s]
200
4,9 41,0 4 1,0 49 5 5 4 7
200
6,2 33,0 5 1,0 62 6 6 5 9
200
7,7 26,0 5 1,5 77 6 6 5 11
200
9,6 21,0 7 1,5 96 7 7 7 13
200
11,4 17,6 8 1,5 114 8 8 8 15
200
11,9 17,0 8 1,5 119 8 8 8 16
200
14,7 13,6 10 2,0 147 9 9 10 19
200
18,2 11,0 12 2,0 182 10 11 12 23
200
22,4 9,0 14 2,5 224 11 12 14 28
200
27,4 7,4 16 3,0 274 13 15 16 34
225
5,5 41 5 1,0 55 5 5 5 8
225
6,9 33 6 1,0 69 6 6 6 10
225
8,6 26,0 7 1,5 86 7 7 7 12
225
10,8 21,0 8 1,5 108 8 8 8 15
225
12,8 17,6 10 2,0 128 8 8 10 17
225
13,4 17 10 2,0 134 8 9 10 18
225
16,6 13,6 12 2,0 166 9 10 12 21
225
20,5 11,0 15 2,5 205 10 12 15 26
225
25,2 9,0 17 2,5 252 12 14 17 31
225
30,8 7,4 20 3,0 308 14 16 20 38
250
6,2 41 6 1,0 62 6 6 6 9
250
7,7 33 7 1,5 77 6 6 7 11
250
9,6 26 8 1,5 96 7 7 8 13
250
11,9 21,0 10 1,5 119 8 8 10 16
250
14,2 17,6 12 2,0 142 9 9 12 19
250
14,8 17,0 12 2,0 148 9 9 12 19
250
18,4 13,6 15 2,0 184 10 11 15 23
250
22,7 11,0 18 2,5 227 11 13 18 28
250
27,9 9,0 21 3,0 279 13 15 21 34
250
34,2 7,4 25 3,0 342 15 18 25 42
in welding area
Table for PE
bead-up heat-up
Additional to the given bead-up force and to the welding force the moving force of the support must be added !
welding area
P (N/mm²)
30.06.2011 Working instructions WIDOS 5100 Page 26/ 1 of 48

Table of Contents

Related product manuals