EasyManuals Logo

Wilo MHiKE Series User Manual

Wilo MHiKE Series
30 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #3 background imageLoading...
Page #3 background image
APPLICATION OF THE PUMP
PHM VI NG DNG
The pump is suitable for boosting low water pressure in apartment houses, apartments, weekend cottages, inns, houses, small
sprinklers, school buildings, dormitories, and other buildings, providing constant water pressure.
Máy bơm phù hp vi mc đích bơm tăng áp lc nước mc độ thp n định dùng cho nhà , căn h, nhà ngh, nhà tr, thiết
b phun c nh, trường hc, ký túc xá và các địa đim khác.
SPECIFICATIONS OF THE PUMP
QUY CÁCH K THUT MÁY BƠM
The embedded converter for constant pressure enables control of the operating pressure depending on the height of a building.
B biến tn tích hp sn cho phép điu khin áp sut vn hành n định, tùy theo chiu cao ca tòa nhà.
Pressure gauge is engaged to show pump pressure.
Áp kế có chc năng hin th áp sut máy bơm.
Pressure tank is attached to prevent rapid change of pressure in piping.
Bình áp sut có nhim v ngăn chn s thay đổi áp sut nhanh bên trong đường ng dn.
The stainless steel pump and brass piping will remain free of rust stains.
Máy bơm bng Inox và đường ng dn bng đồng giúp loi b mi vết r sét.
* Water flow rate, water pressure(head), voltage, motor output are referred to on the nameplate.
Lưu lượng nước, áp lc nước (ct áp), đin áp và công sut động cơ được ghi rõ trên nhãn máy.
Basic conditions are:
Dưới đây là các điu kin cơ bn:
Ambient temperature
Nhit độ môi trường bao
quanh
0~40°C (32~104°F) Location
V trí
Indoors
Trong nhà
Ambient humidity
Độ m môi trường bao
quanh
A relative humidity under
90% (no condensation)
Độ m tương đối < 90%
(không ngưng t)
Suction condition
Điu kin hút
in pressurized condition (recommended)
suction pressure: 0.2kgf/cm
2
điu kin chu áp (khuyến cáo)
Áp lc hút: 0.2kgf/cm
2
Inverter control
Điu khin b biến tn
Vector + VVVF
Power consumption
Tiêu th đin
Single phase
220/230V 50/60Hz
Mt pha
220/230V, 50/60Hz
Pump
Máy bơm
centrifugal pump (horizontal multi-stage
stainless steel pump)
Máy bơm ly tâm (máy bơm Inox đa tng
cánh trc ngang)
FEATURES
ĐẶC ĐIM
Adjusting pressure setting
Điu chnh được áp sut cài đặt
Overpressure protection
Bo v quá áp
Auto restart after electricity failure
T khi động li sau khi mt đin
Auto restart after correcting errors
T khi động li sau khi li được khc phc.
Dry running protection and zero flow detection
Bo v chy khô và không có lưu lượng.
Optional operating modes: Pressure regulation mode, Constant speed mode, External signal control
Các chế độ vn hành: chế độ điu tiết áp sut, chế độ tc độ n định, điu khin tín hiu ngoài
Auto tuning system with two 32bit hi-speed CPU
H thng t động tinh chnh vi b x lý trung tâm tc độ cao 32 bit
Information and alarm signs are indicated on the display, helping easy search
Các biu tượng thông tin và cnh báo được hin th trên màn hình, giúp tìm kiếm d dàng.
Low-noise operation
Hot động vi độ n thp
Energy-saving operation
Tiết kim năng lượng khi hot động
Warm-up function
Chc năng sưởi máy
Alternative operation
Vn hành luân phiên
STAINLESS HORIZONTAL MULTI-STAGE PUMP
MÁY BƠM INOX ĐA TNG TRC NGANG
The pump forms block-typed structure and every pump parts in contact with water is corrosion resistant. (Approved by KTW
and WRC).
Máy bơm có cu to nguyên khi và mi b phn tiếp xúc nước đều có kh năng chng chu s ăn mòn. (Phê duyt bi KTW
WRC).
The pump is equipped with Mono-Shaft, general-purpose mechanical seal, and plugs for suction and discharge.
Máy bơm lin trc được trang b pht cơ khí và các khp ni hút và x.

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Wilo MHiKE Series and is the answer not in the manual?

Wilo MHiKE Series Specifications

General IconGeneral
BrandWilo
ModelMHiKE Series
CategoryWater Pump
LanguageEnglish

Related product manuals