WinGD WARTSILA RT-flex58T-E - Page 5

Summary for Maintenance Manual
(MM)
Page No. Title Subject
Date No.
new exch.
2013 Issue 2013
x
Date of publication 2013-02-26
0002-1/A1 x
Index 3 x
0011-1/A1 (1)
Safety Measures and
Warnings
Attention concerning clean areas (no water or cleaning fluids)
added
x
0330-1/A1
(18, 19)
Clearance Table Key No. 6 and 7: points A and B added x
0352-1/A1 (3) Tightening Values 2722: Values for injection valves with FAST specified x
0380-1/A1 (2) Maintenance Schedule
3103-1: Interval changed "according to classification society"
x
(3)
3403-1: Intervals changed to 18 000-36 000 operating hours
3403-4: Intervals changed to 500-1000 operating hours
3425-1: Work to be carried out and intervals changed
x
2303-1/A1
(1, 7)
EAAD084619 Piston Rod Gland Recess applied on clamping ring 94345b as shown in Fig. 'G' x
2708-3/A1 EAAD084562 Cylinder Cover Version with injection valve with FAST (Fig. B) added x
2722-1/A2
(1-6, 9)
Injection Valve
System oil as test media mentioned; Sec. 3: keeping opening
pressure changed from 10 to 30 seconds; Sec. 4, 5 revised;
tools 94011A, 94269A-55, 94269B, 94269C-41, 94269C-55,
94273, 94275 added
x
3103-1/A1
Measuring Crank
Deflection
1. General aspects; 2. Condition of measuring and 4. Crank
deflection limits revised
x
3425-1/A1
Piston Rings
(Four Piston Rings)
Determination of wear rate of chrome-ceramic piston rings and
measuring piston ring grooves introduced
x
3425-1/A2
Piston Rings
(Three Piston Rings)
Determination of wear rate of chrome-ceramic piston rings and
measuring piston ring grooves introduced
x
4103-3/A1 (5)
Replacing Gear Wheel
on Crankshaft
Stud side (thread) to be applied with MOLYKOTE and
LOCTITE 262 corrected
x
5801-1/A2 (1) Regulating Linkage
(with Woodward ProAct II Analog Actuator): 2nd sentence
about configuration and setting procedure added
x
8733-1/A1
(1, 2)
EAAD084136
HP Pipe to Injection
Valve
Special spanner 94874 and detail concerned in Fig. 'B' added x
9403-5/A1
(3, 14, 15, 33,
34)
Tool List
Tools 94011A, 94269A-55, 94269B, 94269C-41, 94269C-55,
94270F, 94270AF, 94273, 94275, 94291A, 94356 (only figure
modified) and 94357 added
x
Date of publication 2013-08-23
9403-5/A1
(3,4,10,21,26,
27,28,29,35)
2014-01 Tool List
94011A deleted 94012 changed to 94012C, GF94020 changed
to 94020D, 94022 changed to 94022B,94142 changed to
94142-L and -R,
94345F changed to 94345F/94345G,94651 changed to
94651C, 94662 deleted, 94481 deleted,94870E,F,G changed
to 94870K,94870A,B,C changed to 94870J
x
Date of publication 2014-01-09
9403-5/A1 (36) 2014-04 Tool List Tools: 94211, 94212 deleted x
Date of publication 2014-04-02
0020-1/A1 2015-08 Table of Contents New instruction for HP injection pipe with ICU Mk3 8733-1/A2 x
0352-1/A1 (1) 2015-08 EAAD086016 Tightening Values
New tightening values for elastic studs of cylinder cover (new
pre-tensioning jack)
x
2124-3/A1 (2) 2015-08 EAAD085111
Cylinder Liner -
Redressing Lubricating
Grooves and
Scavenge Ports
Fig. A Illustration of cylinder liner replaced (Oil Grooves) x
2708-2/A1 2015-08 EAAD086016
tensioning of cyl.
Cover studs
new pretensioning jack for cyl. Cover CF94215 x
2722-1 (1, 9,
10)
2015-08 Injection valve New tool for removal and installation of nozzle tip x
2013-08
Table of Contents
3425-1/A2: checking wear of … ring grooves added
Manual
Modification Service
Engine Documentation
RT-flex58T-E
Modification
Page or
1/2 10/04/2018