To Next Page
V
Victoria FloresAug 17, 2025
How to record voice on Wisenet XNP-6120H?
- BBrian PerezAug 17, 2025
To record voice on your Wisenet Security Camera, you must enable the check box in - .
How to record voice on Wisenet XNP-6120H?
To record voice on your Wisenet Security Camera, you must enable the check box in - .
What to do if Wisenet XNP-6120H Security Camera reports that NAS setting has failed?
If your Wisenet Security Camera reports a failed NAS setting, take the following steps: First, make sure the NAS IP address is valid. Second, verify the NAS ID and password are correct. Third, confirm you can access the default folder using the NAS ID. Fourth, ensure NAS SMB/CIFS items are unchecked. Fifth, confirm the NAS and camera IP addresses are in the same format. Finally, check if you're trying to access as another user without formatting the default folder, and confirm you're using recommended NAS equipment.
Why does Wisenet Security Camera viewer get disconnected during monitoring?
A viewer might disconnect during monitoring on your Wisenet Security Camera if there are any changes to the camera or network configurations. Check all network connections to ensure they are stable. If the camera is connected over a PPPoE network, poor network conditions could also cause disconnections.
What to do if Wisenet XNP-6120H does not operate properly with Micro SD memory card?
If your Wisenet Security Camera isn't working correctly with a Micro SD card inserted, first check that the card is inserted in the correct direction. Note that the camera might not support memory cards formatted by other devices. If this is the case, format the memory card again in the camera's ? ? menu.
What to do if no video is displayed on Wisenet Security Camera plug-in free webviewer on Safari via HTTPS?
If you're not seeing video on the plug-in free webviewer on Safari via HTTPS for your Wisenet Security Camera, when the authentication popup window appears upon initial access, click "View Authentication Certificate" and select the "Always trust when connecting to the designated webviewer IP" check box. If the webviewer continues to fail, exit the Safari browser by pressing the command key + Q, then access again and repeat the steps above.
Why Wisenet Security Camera cannot record in the NAS?
If your Wisenet Security Camera cannot record to the NAS, confirm that the information registered in the NAS is correct.
What to do if Wisenet Security Camera cannot record into the Micro SD memory card?
If your Wisenet Security Camera cannot record into the Micro SD memory card, check if the memory card is defective.
Why does the microphone sound volume change periodically when accessing Wisenet XNP-6120H Security Camera web viewer on Windows 10?
If you're experiencing periodic changes in microphone sound volume when accessing the web viewer on Chrome or Firefox as a Windows 10 user, this occurs when the microphone driver is set to Realtek driver. Install the High Definition Audio device (Windows Default Driver) or a third party driver as the microphone driver.
Why do images overlap on my Wisenet Security Camera?
Images may overlap on your Wisenet Security Camera if two or more cameras are set to a single multicast address instead of different addresses. Check that each camera has a unique multicast address.
What to do if Wisenet Security Camera motion detection is enabled, but no notification e-mail is received?
If motion detection is enabled on your Wisenet Security Camera, but you're not receiving notification emails, first check the settings. Next, ensure is set to . Finally, verify the option in the menu is checked.
General| Model | XNP-6120H |
|---|---|
| Sensor Type | 1/2.8" CMOS |
| Lens Type | Motorized Varifocal |
| Focal Length | 2.8 ~ 12 mm |
| Optical Zoom | 4x |
| Digital Zoom | 16x |
| Day/Night | Yes (ICR) |
| Video Compression | H.265, H.264, MJPEG |
| Ingress Protection | IP66 |
| Impact Protection | IK10 |
| Resolution | 1920x1080 (Full HD) |
| Minimum Illumination | 0.05 lux (Color), 0.01 lux (B/W) |
| Wide Dynamic Range (WDR) | 120dB |
| Audio | Line in/out |
| Network Interface | RJ45 10/100/1000Mbps |
| Power Input | PoE (802.3af) or 12V DC |
| Power Consumption | Max 15 W |
| Operating Temperature | -30°C ~ +60°C |
| Weight | 1.2kg |
