What to do if my Worx WX427 Saw will not start?
If your Worx Saw won't start, it might be due to a few reasons. First, check that the power cord is properly plugged into a working outlet. If the cord is intact but the saw still won't start, the carbon brush may be worn down and need replacing by a qualified maintenance person.
What to do if my Worx WX427 Saw won't start?
If your Worx Saw isn't starting when you use the on/off switch, first ensure the power cord is securely plugged into a working outlet. If the cord is intact and plugged in, the carbon brush may be worn down, and you should have it replaced by a qualified maintenance person.
Why does my Worx WX427 Saw blade spin or slip?
If your Worx Saw blade spins or slips, it could be because the blade is not tightly engaged with the spindle.
What to do if the cutting depth of my Worx WX427 is less than set?
If the cutting depth of your Worx Saw is less than what you've set, sawdust may have accumulated at the rear of the base. Shake out the sawdust.
What to do if Worx Saw blade kicks back when beginning a cut?
If the Worx Saw blade kicks back when starting a cut, ensure the blade reaches full speed before cutting. This should resolve the issue.
Why is the cutting depth of my Worx Saw less than set?
If the cutting depth of your Worx Saw is less than expected, consider these potential causes: * Sawdust accumulation: Clear any sawdust from the rear of the base, and consider using a vacuum for dust collection. * Blade engagement: Ensure the blade is tightly secured to the spindle, referring to the blade installation section for proper reassembly. * Blade sharpness: Replace the blade with a new, sharp one. * Improper mounting: Verify the blade is correctly mounted. * Guiding issues: Use an edge guide for proper saw guidance.
Why does my Worx WX427 Saw blade not cut a straight line?
If your Worx Saw blade won't cut a straight line, it could be because the blade is dull. Try mounting a new, sharp blade on the saw.
What to do if Worx WX427 cutting depth is less than set?
If the cutting depth of your Worx Saw is less than what you've set, it's possible that sawdust has accumulated at the rear of the base. Shake out the sawdust to resolve this.
What to do if the Worx Saw power cord is not plugged in?
Ensure the power cord of your Worx Saw is securely plugged into a working electrical outlet.
How to fix cutting depth less than set on Worx WX427 Saw?
If the cutting depth of your Worx Saw is less than set, try these steps: * Shake out any sawdust accumulated at the rear of the base. You might consider connecting a vacuum for dust collection. * Remove the blade and reassemble it, ensuring it is tightly engaged with the spindle. * Mount a new, sharp blade. Check that the blade is properly mounted and use a parallel guide.
Precautions to prevent electric shock hazards during tool operation.
Measures for operator alertness and protection during power tool use.
Instructions for replacing the saw blade, including safety measures.
General| Product color | Black, Orange, Stainless steel |
|---|---|
| Protection class | II |
| Blade bore | 9.5 mm |
| Blade diameter | 120 mm |
| Idle speed (max) | 3700 RPM |
| Sound power level | 87 dB |
| Blade diameter (min) | 115 mm |
| Cutting depth (45º) | 30 mm |
| Cutting depth (90º) | 46 mm |
| Sound pressure level | 76 dB |
| Sound level uncertainty | 3 dB |
| Saw blade included | Yes |
| Vibration emission | 6.82 m/s² |
| Input power | 710 W |
| Power source | AC |
Weight and Dimensions| Weight | 2300 g |
|---|
To Next Page
