Xerox
®
B305/B315 Multifunction
Printer Quick Reference Guide
Copy
MMaakkiinngg CCooppiieess
1. Load an original document into the ADF tray or on the scanner
glass.
Note: To avoid a cropped image, make sure that the original
document and output have the same paper size.
2. From the home screen, touch Copy, and then specify the number
of copies.
If necessary, adjust the copy settings.
3. Copy the document.
Note: To make a quick copy, from the control panel, press
the Start button.
CCooppyyiinngg oonn BBootthh SSiiddeess ooff tthhee PPaappeerr
1. Load an original document into the ADF tray or on the scanner
glass.
2. From the home screen, touch Copy > Sides.
3. Adjust the settings.
4. Copy the document.
CCooppyyiinngg MMuullttiippllee PPaaggeess oonnttoo aa SSiinnggllee SShheeeett
1. Load an original document into the ADF tray or on the scanner
glass.
2. From the home screen, touch Copy > Pages per Side.
3. Adjust the settings.
4. Copy the document.
Email
CCoonnffiigguurriinngg tthhee EEmmaaiill SSMMTTPP SSeettttiinnggss
Configure the Simple Mail Transfer Protocol (SMTP) settings to send a
scanned document through e-mail. The settings vary with each email
service provider.
Before you begin, make sure that the printer is connected to a
network and that the network is connected to the Internet.
UUssiinngg tthhee EEmmaaiill SSeettuupp WWiizzaarrdd iinn tthhee PPrriinntteerr
Before using the wizard, make sure that the printer firmware is
updated. For more information, refer to Updating Firmware.
1. From the home screen, touch Email.
2. Touch and type your e-mail address.
3. Type the password.
• Depending on your e-mail service provider, type your account
password, app password, or authentication password. For
more information on the password, refer to the list of Email
Service Providers, and then look for Device Password.
• If your provider is not listed, contact your provider and ask for
the Primary SMTP Gateway, Primary SMTP Gateway Port, Use
SSL/TLS, and SMTP Server Authentication settings.
4. Touch OK.
UUssiinngg tthhee SSeettttiinnggss MMeennuu iinn tthhee PPrriinntteerr
1. From the home screen, touch Settings > E-mail > E-mail Setup.
2. Configure the settings.
• For more information on the password, refer to the list of
Email Service Providers.
• For email service providers that are not on the list, contact
your provider and ask for the settings.
UUssiinngg tthhee EEmmbbeeddddeedd WWeebb SSeerrvveerr
1. Open a web browser, and then type the printer IP address in the
address field.
• View the printer IP address on the printer home screen. The IP
address appears as four sets of numbers separated by periods,
such as 123.123.123.123.
• If you are using a proxy server, then temporarily disable it to
load the web page correctly.
2. Click Settings > Email.
3. From the Email Setup section, configure the settings.
• For more information on the password, refer to the list of
Email Service Providers.
• For email service providers that are not on the list, contact
your provider and ask for the settings.
4. Click Save.
EEmmaaiill SSeerrvviiccee PPrroovviiddeerrss
To determine the SMTP settings of your email service provider, use the
following tables.
Gmail
™
Note: Make sure that two-step verification is enabled on your
Google account.
To enable two-step verification, go to the Google Account Security
page, log in to your account, then from the Signing in to Google
section, click 2-Step Verification.
SETTING VALUE
Primary SMTP
Gateway
smtp.gmail.com
Primary SMTP
Gateway Port
587
1
To Next Page
Need help?
General
Weight and Dimensions
