Why isn't my iPhone/iPod charging when using the Wireless System for iPod with my Yamaha Amplifier?
If your iPhone/iPod isn't charging when using the Wireless System for iPod with your Yamaha Amplifier, ensure that: * The unit is turned on or set to standby mode. * The YID-W10 transmitter is securely stationed in the YID-W10 receiver.
Why does my Yamaha A-S500 Amplifier turn off suddenly?
If your Yamaha Amplifier turns off suddenly and the POWER indicator blinks, several issues could be the cause. First, check the speaker wires to ensure they are not touching each other or shorting against the rear panel; connect them properly. Next, verify that the IMPEDANCE SELECTOR switch is correctly set. Also, excessive input, volume, or internal temperature can activate the protection circuitry; decrease the volume and allow the unit to cool down for about 30 minutes. If the issue persists, the unit may have been exposed to a strong electric shock; set it to standby, disconnect the power cable for 30 seconds, and then reconnect it. If an unusual odor or noise is generated, immediately disconnect the power cable and contact a service center.
How to fix no sound on Yamaha Amplifier?
If there is no sound from your Yamaha Amplifier, first ensure that the sound is not muted by checking the MUTE button on the remote or the VOLUME control. Verify that all cables, including stereo cables and speaker wires, are correctly connected. Make sure that the connected component is turned on and playing. Select the appropriate input source using the INPUT selector on the front panel or the remote. Finally, confirm that the SPEAKERS selector is set to A, B, or A+B as needed.
What to do if my Yamaha Amplifier has no sound?
If your Yamaha Amplifier has no sound, first, ensure that the sound is not muted by checking the MUTE button on the remote control or the VOLUME control. Then, verify that all cables are connected correctly. Make sure the component connected to the amplifier is playing and the correct input source is selected on the amplifier. Finally, check that the SPEAKERS selector is set to A, B, or A+B.
Why can I only hear sound from one speaker on my Yamaha A-S500 Amplifier?
If you only hear sound from one speaker with your Yamaha Amplifier, check the cable connections to ensure they are properly connected. If the problem continues, the cables may be defective. Also, verify that the BALANCE control is set to the appropriate position.
How to fix a 'humming' sound from Yamaha Amplifier?
If you're hearing a humming sound from your Yamaha Amplifier, try these solutions: * Incorrect cable connections. Connect the audio plugs firmly. If the problem persists, the cables may be defective. * No connection from the turntable to the GND terminal. Make the GND connection between the turntable and this unit.
What causes a lack of bass and no ambience in Yamaha A-S500 sound?
If you're experiencing a lack of bass and no ambience with your Yamaha Amplifier, it might be due to the + and – wires being connected in reverse at the amplifier or the speakers. Connect the speaker wires to the correct + and – phase.
What to do if Yamaha Amplifier is not turned on?
If your Yamaha Amplifier is not turning on and the POWER indicator is not lit, first check that the power cable is firmly connected. If it still doesn't turn on, and you are using the remote control, ensure that you press the A switch on the front panel to ON. If the problem persists, disconnect the power cable and contact the nearest authorized Yamaha dealer or service center. If an unusual odor or noise is generated from the unit, do not turn on the power, disconnect the power cable, and contact a service center for repair.
What to do if Yamaha A-S500 is not turning on?
If your Yamaha Amplifier isn't turning on and the POWER indicator is off, first, ensure the power cable is firmly connected. If you're using the remote, make sure to press the A switch on the front panel to ON, not the remote. If problems persist, disconnect the power cable and contact an authorized Yamaha dealer, especially if you notice any unusual odors or noises.
How to fix a Yamaha A-S500 Amplifier remote control that is not working?
If the remote control for your Yamaha Amplifier is not working, make sure you are within a maximum range of 6 m (20 ft) and no more than 30 degrees off-axis from the front panel. If that's not the problem, replace all the batteries in the remote control.
General| Frequency range | 10 - 1000 Hz |
|---|---|
| RMS rated power | 85 W |
| Audio output channels | 2.0 channels |
| Signal-to-Noise Ratio (SNR) | 100 dB |
| Total Harmonic Distortion (THD) | 0.015 % |
| Multichannel audio input type | RCA |
| Multichannel audio output type | Terminals |
| Display | - |
| Product color | Silver |
| Audio decoders | Dolby Digital |
| Ethernet LAN | No |
| Power consumption (standby) | 0.5 W |
| Dimensions (WxDxH) | 435 x 387 x 151 mm |
Weight and Dimensions| Weight | 10300 g |
|---|
Details of buttons, switches, and indicators on the amplifier's front panel.
Instructions for using the remote control, including battery installation and handling.
Description of input/output jacks and selector switches on the rear panel for connectivity.
Guide to setting the impedance selector switch based on speaker impedance for safe operation.
Step-by-step instructions for connecting speakers and various audio source devices to the amplifier.
Instructions for setting up a bi-wire speaker connection, including switch settings.
Connecting the power cable and information on Power Management and Voltage Selector switches.
How to select, play, and adjust the volume and tonal quality of audio sources.
Using Bass, Treble, Balance, Loudness, and Pure Direct controls for sound customization.
Instructions on how to record audio from selected sources using the REC OUT feature (A-S500).
Guide to connecting and operating an iPhone/iPod via a Yamaha Universal Dock.
Instructions for connecting and operating an iPhone/iPod using the Wireless System for iPod.
Solutions for problems with remote control operation, battery replacement, and handling.
Troubleshooting common problems with iPhone/iPod docks and wireless systems.
Detailed technical specifications for audio performance, power output, and frequency response.
General specifications including power supply, consumption, dimensions, and weight.
To Next Page
