What to do if my Yamaha DSP-AX757SE Receiver has no sound?
If your Yamaha Receiver isn't producing any sound, there might be a few reasons: 1. The impedance setting could be incorrect. Ensure it's set to match your speakers. 2. If an optimizer microphone is connected, disconnect it. 3. Check that all speaker connections are secure. 4. The sound might be muted; press the MUTE button to cancel muting.
What should I do if my Yamaha Stereo Receiver shows 'E-5:NOISY'?
If your Yamaha Stereo Receiver displays 'E-5:NOISY', it means background noise is too loud. To solve this: * Try running the auto setup procedure again in a quieter environment. * Turn off or move noisy electrical equipment like air conditioners away from the optimizer microphone.
Why does my Yamaha Stereo Receiver show 'W-1:OUT OF PHASE'?
The 'W-1:OUT OF PHASE' message on your Yamaha Stereo Receiver indicates that the speaker polarity might not be correct. Although this message can appear even with correct connections, you should check the speaker connections to ensure proper polarity (+ / –).
What does 'E-8:NO SIGNAL' mean on my Yamaha Stereo Receiver and how to fix it?
The 'E-8:NO SIGNAL' error on your Yamaha Stereo Receiver indicates that the optimizer microphone isn't detecting test tones. To resolve this: * Verify the microphone setting. * Check both the speaker connections and their placement.
What to do if my Yamaha Stereo Receiver displays 'E-1:NO FRONT SP'?
If your Yamaha Stereo Receiver displays 'E-1:NO FRONT SP', it means the front L/R channel signal(s) is (are) not detected. Try these solutions: * Select the front speakers using SPEAKERS A/B. * Check the front left and right speaker connections. * If you're using an external amplifier for the front speakers, ensure it is powered on.
How to troubleshoot if only one speaker works on Yamaha Receiver?
If only one speaker is working on your Yamaha Receiver, the issue might be due to: * Incorrect cable connections. Double-check and properly connect all cables. If the problem persists after checking the connections, then * Incorrect balance settings. Adjust the SPEAKER LEVEL settings in the SET MENU.
Why is there no sound from my Yamaha Stereo Receiver speakers when headphones are connected?
If you're not getting sound from your speakers, it might be because headphones are connected. Unplug the headphones.
What to do if sound from Yamaha Receiver is not output correctly?
If the sound isn't output correctly from your Yamaha Receiver, consider the following: * The impedance setting might be incorrect; set it to match your speakers. * If the input mode is set to DTS, select AUTO. * Ensure all speaker connections are secure. * Check if the volume is turned down; increase it.
Why does my Yamaha DSP-AX757SE Receiver display 'Check SP Wires'?
If your Yamaha Receiver displays a 'Check SP Wires' message, it indicates that the speaker cables are short-circuited. Ensure all speaker cables are correctly connected.
Essential safety guidelines for operating the audio/video equipment.
Recommendations for positioning front, surround, and other speakers for optimal sound.
Instructions on how to properly connect speaker cables to the unit's terminals.
Setting the unit's impedance to match connected speakers.
Overview of the YPAO system for automatic speaker adjustment.
Instructions for positioning the microphone for the auto setup procedure.
Step-by-step guide to initiating the automatic speaker setup process.
Solutions for common error messages encountered during auto setup.
Fundamental steps for turning on the unit, selecting sources, and adjusting volume.
Fine-tuning the output level for individual speakers for optimal balance.
Adjusting speaker size, levels, distance, and equalizer settings.
Configuring speaker impedance and resetting unit parameters to factory defaults.
Setting up a multi-room audio system and required equipment.
Using the remote control to operate Zone 2 functions and select sources.
Adjusting DSP effect levels and the perceived distance of sound sources.
Adjusting the perceived size and reflectivity of the sound field.
Controlling the duration, delay, and volume of reverberation effects.
Adjusting dialog clarity and individual channel volume levels.
Solutions for common problems like unit not turning on or no display.
To Next Page
General