Why is there no sound from the effect speakers on my Yamaha HTR-5540 Receiver?
If you are not getting any sound from the effect speakers on your Yamaha Receiver: * Ensure the sound effect is turned on by pressing STEREO/EFFECT. * If using a Dolby Surround, Dolby Digital, or DTS decoding DSP program, make sure the material is encoded with Dolby Surround, Dolby Digital, or DTS. Otherwise, select another DSP program.
Why is there no sound from the center speaker on my Yamaha Receiver?
If there is no sound from the center speaker of your Yamaha Receiver: * Check if the output level of the center speaker is set to minimum and raise the level if needed. * Verify that “1A CENTER” on the SET MENU is not set to NON; select the appropriate mode for your center speaker. * Ensure that you have not selected one of the Hi-Fi DSP programs (1 to 4), except for 5ch Stereo; if so, select another DSP program.
Why does my Yamaha HTR-5540 Receiver fail to turn on?
If your Yamaha Receiver fails to turn on or enters standby mode shortly after being turned on, consider the following: * Ensure the power cord is firmly connected. * Verify the IMPEDANCE SELECTOR switch on the rear panel is fully set to either the left or right position while the unit is in standby mode. * Check speaker wire connections to ensure they are secure and not touching anything other than their respective connections, as the protection circuitry may have been activated. * If the unit was exposed to a strong external electric shock, set it to standby mode, disconnect the power cord, plug it back in after 30 seconds, and then try operating it again.
Why is there no sound from the subwoofer on my Yamaha Receiver?
If there is no sound from the subwoofer connected to your Yamaha Receiver: * Check if “1D BASS” on the SET MENU is set to MAIN when playing a Dolby Digital or DTS signal; if so, select SWFR or BOTH. * If playing a 2-channel source, and “1D BASS” is set to SWFR or MAIN, change it to BOTH.
How to fix Yamaha HTR-5540 when only one speaker side can be heard?
If you only hear sound from one speaker on your Yamaha Receiver: * Ensure the cable connections are correct; reconnect them properly, and if the problem persists, the cables may be defective. * Check the “5 L/R BALANCE” setting on the SET MENU and adjust it to the appropriate position.
What to do if my Yamaha HTR-5540 Receiver is producing a 'humming' sound?
If you hear a 'humming' sound from your Yamaha Receiver, firmly connect the audio plugs. If the problem continues, the cables may be defective.
Why is there no sound from the effect speakers on my Yamaha Stereo Receiver?
If there is no sound coming from the effect speakers on your Yamaha Stereo Receiver, check the following: * Ensure the sound effect is turned on by pressing STEREO/EFFECT. * If you're using a Dolby Surround, Dolby Digital, or DTS decoding DSP program, make sure the material is encoded with Dolby Surround, Dolby Digital, or DTS. If not, select another DSP program.
Why is there no sound from the rear speakers on my Yamaha Stereo Receiver?
If you are not getting any sound from the rear speakers connected to your Yamaha Stereo Receiver, check these: * Make sure the output level of the rear speakers is not set to minimum. Increase the output level. * If you are playing a monaural source with program 9, select another DSP program.
Why is there no sound coming from the center speaker of my Yamaha Stereo Receiver?
If there's no sound from the center speaker of your Yamaha Stereo Receiver, try the following: * Increase the output level of the center speaker. * Check that “1A CENTER” in the SET MENU is set to the appropriate mode for your center speaker (not NON). * Ensure you haven't selected one of the Hi-Fi DSP programs (1 to 4), except for 5ch Stereo. If so, select another DSP program.
Why is there no sound from the subwoofer on my Yamaha Stereo Receiver?
If you're not getting any sound from the subwoofer connected to your Yamaha Stereo Receiver, check the following settings in the SET MENU: * If “1D BASS” is set to MAIN while playing a Dolby Digital or DTS signal, change it to SWFR or BOTH. * If “1D BASS” is set to SWFR or MAIN while playing a 2-channel source, change it to BOTH.
General| Tuner | AM/FM |
|---|---|
| Weight | 22.1 lbs |
| Signal-To-Noise Ratio | 100 dB |
| Total Harmonic Distortion | 0.06% |
| Input Impedance | 47 kOhm |
| Input Sensitivity | 200 mV |
| Surround Sound | Dolby Digital, DTS, Dolby Pro Logic II |
| Digital Audio Inputs | 2 x Optical, 1 x Coaxial |
| Video Inputs | 3 Composite |
| Video Outputs | 1 composite video output |
| Response Bandwidth | 10 Hz - 100 kHz |
| Audio D/A Converter | 24-bit / 96 kHz |
| Built-in Decoders | Dolby Digital, DTS, Dolby Pro Logic II |
| Surround Sound Effects | Virtual Cinema DSP |
| Dimensions (W x H x D) | 17-1/8" x 6-3/8" x 15-1/4" |
| Amplifier Output Details | 75 W - 8 Ohm - 20 Hz to 20 kHz - THD 0.06% - 5 channel(s) (surround) |
Guides on optimal positioning and connection of speakers for the best sound field quality.
Instructions for correctly connecting speaker cables to the unit's terminals, ensuring proper polarity.
Steps to follow to turn on the AV receiver and connected components after all connections are made.
How to balance speaker output levels using the test tone generator for optimal sound.
Instructions for automatic and manual tuning of radio stations and storing favorite presets.
Explains how to access and adjust various system settings using the SET MENU on the remote control.
Details on configuring speaker settings based on system configuration and speaker sizes.
Common problems and their solutions for unit operation, sound issues, and connection errors.
To Next Page
