EasyManuals Logo

Yamaha RX-V4600/DSP User Manual

Yamaha RX-V4600/DSP
144 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #25 background imageLoading...
Page #25 background image
RX-V4600/DSP-AX4600
25
RX-V4600/
DSP-AX4600
• Starting DIAG
Press the STANDBY/ON key while simultaneously
pressing those two keys of the main unit as indicated in the
figure below.
●ダイアグの起動
本体の下図に示すキーを同時に押しながらSTANDBY/
ONキーを押すと、ダイアグが起動します。
Starting DIAG in the protection cancel
mode
If the protection function works and causes hindrance to
trouble diagnosis, cancel the protection function as
described below, and it will be possible to enter the DIAG
mode. (The protection functions other than the excess
current detect function will be disabled.)
Press the STANDBY/ON key while simultaneously
pressing those two keys indicated in the figure above. At
this time, keep pressing those two keys for 3 seconds or
longer.
In this mode, the SLEEP segment of the FL display of the
main unit flashes to indicate that the mode is DIAG mode
with the protection functions disabled.
CAUTION!
Using this product with the protection function disabled
may cause damage to itself. Use special care for this point
when using this mode.
●プロテクション解除モードでの起動
プロテクションが動作することにより、故障箇所の診断に
支障をきたすような場合は、次の方法によりプロテクショ
ンを解除した状態でダイアグモードに入ることができま
す。(過電流検出以外のプロテクション動作を解除する)
上図のキーを同時に押しながSTANDBY/ONキーを押
します。このとき、上図のキーを3秒以上押し続けてくだ
さい。
このモードでは本体FLのSLEEPセグメントが点滅し、
プロテクションを解除した状態でのダイアグモードである
ことを知らせます。
注意!
プロテクションを解除した状態でのダイアグモードは、
危険な状態でもプロテクションが作動しないため、動作
させると、機器を破壊することがあります。このモード
を使用する場合は十分注意してください。
●ダイアグの解除
ダイアグを解除する前に、ダイアグメニューNo.11
FACTORYPRESET(メモリーの初期化禁止/またはメ
モリーの初期化の設定をします。
ユーザーメモリーを保持したい場合は、必ず
PRESETINHIBIT(メモリー初期化禁止)を選択して
ください。
本体のSTANDBY/ONキーかリモコンのSTANDBY
キーを押し、パワーオフにします。
• Canceling DIAG
[1] Before canceling DIAG, execute setting for PRESET of
DIAG menu No.11 (Memory initialization inhibited or
Memory initialized).
* In order to keep the user memory stored, be sure to
select PRESET INHIBIT (Memory initialization
inhibited). Any protection history will remain in
memory.
[2] Turn off the power by pressing the STANDBY/ON
key of the main unit or the STANDBY key of the
remote controller.
Keys of main unit/本体キー
Turn on the power while pressing these keys.
これらのキーを同時に押しながら、パワーオンする。

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Yamaha RX-V4600/DSP and is the answer not in the manual?

Yamaha RX-V4600/DSP Specifications

General IconGeneral
BrandYamaha
ModelRX-V4600/DSP
CategoryReceiver
LanguageEnglish

Related product manuals