YASKAWA yasnac lx3 - Page 238

APPENDIX 2 LIST OF PARAMETER NUMBERS (Cent’d)
-r— —7— ~
-, -
:6021
,–_r —.
_D_7 1 D, Ds DA ~ Da __~ D~Do
.
UM09000
D7
1:
Inhibits editing and display and punchout opera-
tions of the part program of program No. 9000
to 9999.
0:
Permits editing and display and punchout opera-
tions.
MERSIN
Dt5
1: Replaces the stored program with a new one
when part program is already stored.
O: Displays ALREADY ALARM.
RSC)NOF D5
1:
Sets on and off RS (RS232C signal) by. “ %“
character.
():
Keeps RS signal on until reading-in is
finished.
CHKDR
D4
1:
Recognizes DR.
O: Does not recognize DR.
O - 9999o D3
1: Punches 00 when tape is punched with O, -,
9, 9, 9, 9 keyed in and ~T- key depressed.
o: Does not punch 00 when tape is punched with
o, -, 9, 9, 9, and 9 keyed in and != key
depressed.
PO:NON
D2
1: Does not clear program No. on power applica-
tion.
(Program number is stored at power supply
shut off.)
o:
Clears program No.
on power application.
PRGNO
D1
1:
Employs the value following address O or N
as the program number (specifiablein one
block) .
0: Employs the value following address O as the
program number.
M02M99
DO
1: Considers M02, M30 and M99 as the program
end when part program is stored into memory.
At punchout with O-9999 depressed, add
EOB in front of O number.
o:
Does not consider M02, M30 and M99 as the
program end when part program is stored
into memory.
At punchout with O-9999
depressed, do not add EOB in front of O
number.
WX322–r “--~– —
——— .——-—— -——
‘ “LD’--!! -3 .->. -E:3 __Do_
-1 -_
HOFSMV
D7
Enables the movement of automatic mode han-
dle offset during cutting feed by interpolation.
Enables the movement of automatic mode han-
dle offset except during execution of rapid
traverse.
TLCC D6
1:
Effective on the next T code when offset
amount is changed.
0: Effective on the next block when offset
amount is changed.
TRDFH D5
1: Executes the block next to the block specify-
ing thread, and stops at single block oper–
ation or feedhold during thread cutting.
o:
Stops on completion of the block specifying
thread at single block operation or feedhold
during thread cutting.
MABIN D4
1:
Ignores manual absolute function for
incremental command by U and W.
o:
Does not ignore manual absolute function for
incremental command by U and W.
ISOPO D3
1.
L.
Does not output parity bit (8th bit)when out-
putting 1S0 codes from NC by operating OUT
key (in the EDIT mode) .
0:
Outputs parity bit.
ISOPI
‘2
1: Ignores parity bit ( 8th bit) when outputting
1S0 codes by operating IN key (in the EDIT
mode) and when reading-in 1S0 tape data in
the TAPE mode.
o: Performs parity check.
HOFSZ, HOFSX
D~, DO
Specifies whether automatic mode handle offset
movement is effective or ineffective.
1:
Effective automatic mode handle offset move-
ment.
o:
Ineffective automatic mode handle offset move-
ment.
A-12