YOKOGAWA DL350 - Page 154

4-127
IM DL350-17EN
Commands
1
2
3
4
5
App
Index
:MEASure:{CHANnel<x1>[:SCHannel<x2>]
|MATH<x3>}:DELay:COUNt?
Function Queries the statistics count of the delay between
channels.
Syntax
:MEASure:{CHANnel<x1>[:SCHannel<x2>]|
MATH<x3>}:DELay:COUNt?
<x1> = 1 to 4, 7
<x2> = 1 to 60 (sub channel)
<x3> = 1, 2
Example
:MEASURE:CHANNEL1:DELAY:COUNT?
-> :MEASURE:CHANNEL1:DELAY:COUNT 3
Description For channels that have sub channels, use the
:MEASure:CHANnel:SCHannel:DELay:COUNt?
command.
:MEASure:{CHANnel<x1>[:SCHannel<x2>]
|MATH<x3>}:DELay:{MAXimum|MEAN|MINim
um|SDEViation}?
Function Queries a statistic of the delay between channels.
Syntax
:MEASure:{CHANnel<x1>[:SCHannel<x2>]|
MATH<x3>}:DELay:{MAXimum|MEAN|
MINimum|SDEViation}?
<x1> = 1 to 4, 7
<x2> = 1 to 60 (sub channel)
<x3> = 1, 2
Example
:MEASURE:CHANNEL1:DELAY:MEAN?
-> :MEASURE:CHANNEL1:DELAY:
MEAN 6.6666667E-06
Description For channels that have sub channels, use the
:MEASure:CHANnel:SCHannel:DELay:{MAXimu
m|MEAN|MINimum|SDEViation}? command.
:MEASure:{CHANnel<x1>[:SCHannel<x2>]
|MATH<x3>}:DELay:MEASure?
Function Queries all the settings for a source waveform
for measuring the delay between channels of a
waveform.
Syntax
:MEASure:{CHANnel<x1>[:SCHannel<x2>]|
MATH<x3>}:DELay:MEASure?
<x1> = 1 to 4, 7
<x2> = 1 to 60 (sub channel)
<x3> = 1, 2
Example
:MEASURE:CHANNEL1:DELAY:MEASURE?
Description For channels that have sub channels, use the
:MEASure:CHANnel:SCHannel:DELay:MEASure
command.
:MEASure:{CHANnel<x1>[:SCHannel<x2>]
|MATH<x3>}:DELay:MEASure:COUNt
Function Sets or queries the number of edges at which
delay between channels will be measured for a
waveform.
Syntax
:MEASure:{CHANnel<x1>[:SCHannel<x2>]|
MATH<x3>}:DELay:MEASure:COUNt {<NRf>}
:MEASure:{CHANnel<x1>[:SCHannel<x2>]|
MATH<x3>}:DELay:MEASure:COUNt?
<x1> = 1 to 4, 7
<x2> = 1 to 60 (sub channel)
<x3> = 1, 2
<NRf> = 1 to 9
Example
:MEASURE:CHANNEL1:DELAY:MEASURE:
COUNT 2
:MEASURE:CHANNEL1:DELAY:MEASURE:
COUNT?
-> :MEASURE:CHANNEL1:DELAY:MEASURE:
COUNT 2
Description For channels that have sub channels, use the
:MEASure:CHANnel:SCHannel:DELay:MEASure:
COUNt command.
:MEASure:{CHANnel<x1>[:SCHannel<x2>]
|MATH<x3>}:DELay:MEASure:SLOPe
Function Sets or queries a source waveform slope that will
be used to measure delay between channels for
a waveform.
Syntax
:MEASure:{CHANnel<x1>[:SCHannel<x2>]|
MATH<x3>}:DELay:MEASure:SLOPe {RISE|
FALL}
:MEASure:{CHANnel<x1>[:SCHannel<x2>]|
MATH<x3>}:DELay:MEASure:SLOPe?
<x1> = 1 to 4, 7
<x2> = 1 to 60 (sub channel)
<x3> = 1, 2
Example
:MEASURE:CHANNEL1:DELAY:MEASURE:
SLOPE RISE
:MEASURE:CHANNEL1:DELAY:MEASURE:
SLOPE?
-> :MEASURE:CHANNEL1:DELAY:MEASURE:
SLOPE RISE
Description For channels that have sub channels, use the
:MEASure:CHANnel:SCHannel:DELay:MEASure:
SLOPe command.
4.22 MEASure Group