YOKOGAWA DL350 User Manual

4-128
IM DL350-17EN
:MEASure:{CHANnel<x1>[:SCHannel<x2>]
|MATH<x3>}:DELay:REFerence?
Function Queries all reference waveform settings used
to measure the delay between channels for the
specified waveform.
Syntax
:MEASure:{CHANnel<x1>[:SCHannel<x2>]|
MATH<x3>}:DELay:REFerence?
Description For channels that have sub channels, use the
:MEASure:CHANnel:SCHannel:DELay:REFeren
ce? command.
:MEASure:{CHANnel<x1>[:SCHannel<x2>]
|MATH<x3>}:DELay:REFerence:COUNt
Function Sets or queries the edge detection count of the
reference waveform used to measure the delay
between channels for the specified waveform.
Syntax
:MEASure:{CHANnel<x1>[:SCHannel<x2>]|
MATH<x3>}:DELay:REFerence:
COUNt {<NRf>}
:MEASure:{CHANnel<x1>[:SCHannel<x2>]|
MATH<x3>}:DELay:REFerence:
COUNt {<NRf>}?
<x1> = 1 to 4, 7
<x2> = 1 to 60 (sub channel)
<x3> = 1, 2
<NRf> = 1 to 9
Example
:MEASURE:CHANNEL1:DELAY:REFERENCE:
COUNT 1
:MEASURE:CHANNEL1:DELAY:REFERENCE:
COUNT?
-> :MEASURE:CHANNEL1:DELAY:
REFERENCE:COUNT 1
Description For channels that have sub channels, use the
:MEASure:CHANnel:SCHannel:DELay:REFerenc
e:COUNt command.
:MEASure:{CHANnel<x1>[:SCHannel<x2>]
|MATH<x3>}:DELay:REFerence:LOGic:BIT
Function Sets or queries the bit of the reference waveform
trace used to measure the delay between
channels for a waveform.
Syntax
:MEASure:{CHANnel<x1>[:SCHannel<x2>]|
MATH<x3>}:DELay:REFerence:LOGic:
BIT {<NRf>}
:MEASure:{CHANnel<x1>[:SCHannel<x2>]|
MATH<x3>}:DELay:REFerence:LOGic:BIT?
<x1> = 1 to 4, 7
<x2> = 1 to 60 (sub channel)
<x3> = 1, 2
<NRf> = 1 to 8
Example
:MEASURE:CHANNEL1:DELAY:REFERENCE:
LOGIC:BIT 1
:MEASURE:CHANNEL1:DELAY:REFERENCE:
LOGIC:BIT?
-> :MEASURE:CHANNEL1:DELAY:
REFERENCE:LOGIC:BIT 1
Description • For channels that have sub channels, use the
:MEASure:CHANnel:SCHannel:DELay:REFere
nce:LOGic:BIT command.
• When the trace specified by the :MEASure:{C
HANnel<x1>[:SCHannel<x2>]|MATH<x3>}:D
ELay:REFerence:TRACe command is a logic
module, specify the bit of that channel.
:MEASure:{CHANnel<x1>[:SCHannel<x2>]
|MATH<x3>}:DELay:REFerence:SLOPe
Function Sets or queries the edge detection slope of the
reference waveform used to measure the delay
between channels for the specified waveform.
Syntax
:MEASure:{CHANnel<x1>[:SCHannel<x2>]|
MATH<x3>}:DELay:REFerence:
SLOPe {RISE|FALL}
:MEASure:{CHANnel<x1>[:SCHannel<x2>]|
MATH<x3>}:DELay:REFerence:SLOPe?
<x1> = 1 to 4, 7
<x2> = 1 to 60 (sub channel)
<x3> = 1, 2
Example
:MEASURE:CHANNEL1:DELAY:REFERENCE:
SLOPE RISE
:MEASURE:CHANNEL1:DELAY:REFERENCE:
SLOPE?
-> :MEASURE:CHANNEL1:DELAY:
REFERENCE:SLOPE RISE
Description For channels that have sub channels, use the
:MEASure:CHANnel:SCHannel:DELay:REFerenc
e:SLOPe command.
4.22 MEASure Group

YOKOGAWA DL350 Specifications

General

Brand	YOKOGAWA
Model	DL350
Category	Recording Equipment
Language	English