YOKOGAWA DL350 User Manual

4-133
IM DL350-17EN
Commands
1
2
3
4
5
App
Index
:MEASure:{XY<x>}:<Parameter>:VALue?
Function Queries the measured value of a X-Y waveform
parameter.
Syntax
:MEASure:{XY<x>}:<Parameter>:
VALue? {<NRf>}
<x> = 1, 2
<NRf> = 1 to 30000
<Parameter> =
{XY1Integ|XY2Integ}
Description • This command returns “NAN” if the value
cannot be measured.
Parameters cannot be measured if the
measurement has not been performed or
if the measurement was performed, but
computations were not performed because the
specified range exceeded 10 Mpoint.
• The <NRf> at the end is used to specify which
iteration of statistical processing to query the
parameter value from. This command returns
“NAN” (Not A Number) if the specified value
does not exist.
- For non-cyclic statistical processing:
<NRf> can be omitted. If you omit , the
most recent history parameter value will be
queried.
If <NRf> is included, the history parameter
value of the waveform <NRf> times before
the newest history waveform will be queried.
- After cyclic statistical processing has been
completed:
<NRf> can be omitted. If you omit , the
parameter value within the cycle that was
measured last will be queried.
If you include <NRf>, the parameter value
within the cycle that was measured <NRf>
times after the measurement shown on the
screen’s left edge will be queried.
:MEASure:CHANnel<x1>:BIT<x2>:ALL
Function Sets the specified bit of the specified channel to
on or off at once.
Syntax
:MEASure:CHANnel<x1>:BIT<x2>:
ALL {<Boolean>}
<x1> = 1 to 6
<x2> = 1 to 8
Example
:MEASURE:CHANNEL1:BIT1:ALL ON
Description This command is valid on logic input channels.
:MEASure:CHANnel<x1>:BIT<x2>:CDEStin
ation
Function Sets or queries whether the copy destination
channel is ON or OFF for when parameter
measurement items are copied between channels
or bits.
Syntax
:MEASure:CHANnel<x1>:BIT<x2>:
CDEStination {<Boolean>}
<x1> = 1 to 6
<x2> = 1 to 8
Example
:MEASURE:CHANNEL1:BIT1:
CDESTINATION ON
Description This command is valid on logic input channels.
:MEASure:CHANnel<x1>:BIT<x2>:COPY
Function Copies the on/off setting of the specified bit of the
specified channel to another specified channel.
Syntax
:MEASure:CHANnel<x1>:BIT<x2>:COPY
<x1> = 1 to 6
<x2> = 1 to 8
Example
:MEASURE:CHANNEL1:BIT1:COPY
Description This command is valid on logic input channels.
:MEASure:CHANnel<x1>:BIT<x2>:DELay?
Function Queries all settings related to the delay of the
specified bit of the specified channel on a logic
module.
Syntax
:MEASure:CHANnel<x1>:BIT<x2>:DELay?
:MEASure:CHANnel<x1>:BIT<x2>:DELay:C
OUNt?
Function Queries the statistics count of the delay of the
specified bit of the specified channel.
Syntax
:MEASure:CHANnel<x1>:BIT<x2>:DELay:
COUNt?
<x1> = 1 to 6
<x2> = 1 to 8
Example
:MEASURE:CHANNEL1:BIT1:DELAY:COUNT?
-> :MEASURE:CHANNEL1:BIT1:DELAY:
COUNT 10
Description This command is valid on logic input channels.
4.22 MEASure Group

YOKOGAWA DL350 Specifications

General

Brand	YOKOGAWA
Model	DL350
Category	Recording Equipment
Language	English