EasyManua.ls Logo

YOKOGAWA DL350 - Page 161

YOKOGAWA DL350
215 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
4-134
IM DL350-17EN
:MEASure:CHANnel<x1>:BIT<x2>:DELay:{
MAXimum|MEAN|MINimum|SDEViation}?
Function Queries the statistical value of the delay of the
specified bit of the specified channel.
Syntax
:MEASure:CHANnel<x1>:BIT<x2>:DELay:
{MAXimum|MEAN|MINimum|SDEViation}?
<x1> = 1 to 6
<x2> = 1 to 8
Example
:MEASURE:CHANNEL1:BIT1:DELAY:MEAN?
-> :MEASURE:CHANNEL1:BIT1:DELAY:
MEAN 6.6666667E-06
Description This command is valid on logic input channels.
:MEASure:CHANnel<x1>:BIT<x2>:DELay:M
EASure?
Function Queries all settings related to the source
waveform used to measure the delay of the
specified bit of the specified channel on a logic
module.
Syntax
:MEASure:CHANnel<x1>:BIT<x2>:DELay:
MEASure?
:MEASure:CHANnel<x1>:BIT<x2>:DELay:M
EASure:COUNt
Function Sets or queries the edge detection count of the
source waveform used to measure the delay of
the specified bit of the specified channel.
Syntax
:MEASure:CHANnel<x1>:BIT<x2>:DELay:
MEASure:COUNt {<NRf>}
:MEASure:CHANnel<x1>:BIT<x2>:DELay:
MEASure:COUNt?
<x1> = 1 to 6
<x2> = 1 to 8
<NRf> = 1 to 9
Example
:MEASURE:CHANNEL1:BIT1:DELAY:
MEASURE:COUNT 2
:MEASURE:CHANNEL1:BIT1:DELAY:
MEASURE:COUNT?
-> :MEASURE:CHANNEL1:BIT1:DELAY:
MEASURE:COUNT 2
Description This command is valid on logic input channels.
:MEASure:CHANnel<x1>:BIT<x2>:DELay:M
EASure:SLOPe
Function Sets or queries the edge polarity of the source
waveform used to measure the delay of the
specified bit of the specified channel.
Syntax
:MEASure:CHANnel<x1>:BIT<x2>:DELay:
MEASure:SLOPe {RISE|FALL}
:MEASure:CHANnel<x1>:BIT<x2>:DELay:
MEASure:SLOPe?
<x1> = 1 to 6
<x2> = 1 to 8
Example
:MEASURE:CHANNEL1:BIT1:DELAY:
MEASURE:SLOPE FALL
:MEASURE:CHANNEL1:BIT1:DELAY:
MEASURE:SLOPE?
-> :MEASURE:CHANNEL1:BIT1:DELAY:
MEASURE:SLOPE FALL
Description This command is valid on logic input channels.
:MEASure:CHANnel<x1>:BIT<x2>:DELay:R
EFerence?
Function Queries all settings related to the reference
waveform used to measure the delay of the
specified bit of the specified channel on a logic
module.
Syntax
:MEASure:CHANnel<x1>:BIT<x2>:DELay:
REFerence?
:MEASure:CHANnel<x1>:BIT<x2>:DELay:R
EFerence:COUNt
Function Sets or queries the edge detection count of the
reference waveform used to measure the delay of
the specified bit of the specified channel.
Syntax
:MEASure:CHANnel<x1>:BIT<x2>:DELay:
REFerence:COUNt {<NRf>}
:MEASure:CHANnel<x1>:BIT<x2>:DELay:
REFerence:COUNt?
<x1> = 1 to 6
<x2> = 1 to 8
<NRf> = 1 to 9
Example
:MEASURE:CHANNEL1:BIT1:DELAY:
REFERENCE:COUNT 2
:MEASURE:CHANNEL1:BIT1:DELAY:
REFERENCE:COUNT?
-> :MEASURE:CHANNEL1:BIT1:DELAY:
REFERENCE:COUNT 2
Description This command is valid on logic input channels.
4.22 MEASure Group

Table of Contents

Other manuals for YOKOGAWA DL350

Related product manuals