4-142
IM DL350-17EN
:SEARch:EVENt?
Function Queries all event search settings.
Syntax
:SEARch:EVENt?
:SEARch:EVENt:COUNt
Function Sets or queries the event search event number.
Syntax
:SEARch:EVENt:COUNt {<NRf>}
:SEARch:EVENt:COUNt?
Manual event
<NRf> = 1 to 100
When capture event is set to On Start
<NRf> = 1 to 500
Example
:SEARCH:EVENT:COUNT 1
:SEARCH:EVENT:COUNT?
-> :SEARCH:EVENT:COUNT 1
:SEARch:EXECute
Function Executes the search. This is an overlap
command.
Syntax
:SEARch:EXECute
:SEARch:LSTate?
Function Queries all logic pattern search settings.
Syntax
:SEARch:LSTate?
:SEARch:LSTate:BIT<x>
Function Sets or queries the level of the specified bit for
logic pattern searches.
Syntax
:SEARch:LSTate:BIT<x> {DONTcare|
HIGH|LOW}
:SEARch:LSTate:BIT<x>?
<x> = 1 to 8
Example
:SEARCH:LSTATE:BIT1 HIGH
:SEARCH:LSTATE:BIT1?
-> :SEARCH:LSTATE:BIT1 HIGH
:SEARch:LSTate:COUNt
Function Sets or queries the logic pattern search count.
Syntax
:SEARch:LSTate:COUNt {<NRf>}
:SEARch:LSTate:COUNt?
<NRf> = 1 to 1000000
Example
:SEARCH:LSTATE:COUNT 100
:SEARCH:LSTATE:COUNT?
-> :SEARCH:LSTATE:COUNT 100
Description This setting is the same as the edge search count
setting.
:SEARch:LSTate:SOURce
Function Sets or queries the trace to perform the logic
pattern search on.
Syntax
:SEARch:LSTate:SOURce {<NRf>[,
<NRf>]}
:SEARch:LSTate:SOURce?
First <NRf> = 1 to 7
Second <NRf> = 1 to 60 (sub channel)
Example
:SEARCH:LSTATE:SOURCE 5
:SEARCH:LSTATE:SOURCE?
-> :SEARCH:LSTATE:SOURCE 5
:SEARch:MAG<x>
Function Sets or queries a zoom waveform magnification.
Syntax
:SEARch:MAG<x> {<NRf>}
:SEARch:MAG<x>?
<x> = 1, 2
<NRf> = 1 to 10000000
Example
:SEARCH:MAG1 1000
:SEARCH:MAG1? -> :SEARCH:MAG1 1000.0
Description This command is valid an external clock is
in use. When the internal clock is use, use
the :SEARch:TDIV<x> command to set the
magnification.
:SEARch:POSition<x>
Function Sets or queries the position of a zoom box.
Syntax
:SEARch:POSition<x> {<NRf>}
:SEARch:POSition<x>?
<x> = 1, 2
<NRf> = –5 to 5 div
Example
:SEARCH:POSITION1−0.7219
:SEARCH:POSITION1?
->:SEARCH:POSITION1−0.721900000000
:SEARch:SELect
Function Sets the search point that is displayed on the
zoom window, and queries the zoom position of
that search point.
Syntax
:SEARch:SELect {<NRf>|MAXimum}
:SEARch:SELect?
<NRf> = 1 to 5000
Example
:SEARCH:SELECT 4
:SEARCH:SELECT?
->:SEARCH:SELECT−0.721900000000
Description The string “NAN” is returned if the search could
not retrieve a position.
:SEARch:SELect? MAXimum
Function Queries the maximum save number, which is the
number that is attached to the last position that
the search retrieved.
Syntax
:SEARch:SELect? MAXimum
Example
:SEARCH:SELECT? MAXIMUM
-> :SEARCH:SELECT 5
Description The string “NAN” is returned if the search could
not retrieve a position.
4.25 SEARch Group
To Next Page
Loading...
Need help?
General
