YOKOGAWA DL350 - Page 184

4-157
IM DL350-17EN
Commands
1
2
3
4
5
App
Index
:TRIGger:ACTion:SAVE:PATH?
Function Queries the path on the storage medium that
waveform data is saved to as an action.
Syntax
:TRIGger:ACTion:SAVE:PATH?
Example
:TRIGger:ACTion:SAVE:PATH?
-> :TRIG:ACT:SAVE:PATH "Path=SD/***"
:TRIGger:AND?
Function Queries all AND trigger settings.
Syntax
:TRIGger:AND?
:TRIGger:AND:CHANnel<x1>:BIT<x2>
Function Sets or queries the state of the specified bit of the
specified logic channel for AND triggers.
Syntax
:TRIGger:AND:CHANnel<x1>:
BIT<x2> {DONTcare|HIGH|LOW}
:TRIGger:AND:CHANnel<x1>:BIT<x2>?
<x1> = 1 to 6
<x2> = 1 to 8
Example
:TRIGGER:AND:CHANNEL5:BIT1 DONTCARE
:TRIGGER:AND:CHANNEL5:BIT1?
-> :TRIGGER:AND:CHANNEL5:
BIT1 DONTCARE
:TRIGger:AND:CHANnel<x1>:SCHannel<x2
>:BIT<x3>
Function Sets or queries the state of the specified bit of
the specified sub channel of the specified logic
channel for AND triggers.
Syntax
:TRIGger:AND:CHANnel<x1>:
SCHannel<x2>:BIT<x3> {DONTcare|HIGH|
LOW}
:TRIGger:AND:CHANnel<x1>:
SCHannel<x2>:BIT<x3>?
<x1> = 1 to 4, 7
<x2> = 1 to 60 (sub channel)
<x3> = 1 to 8
Example
:TRIGGER:AND:CHANNEL1:SCHANNEL1:
BIT1 LOW
:TRIGGER:AND:CHANNEL1:SCHANNEL1:
BIT1?
-> :TRIGGER:AND:CHANNEL1:SCHANNEL1:
BIT1 LOW
:TRIGger:AND:CHANnel<x>[:CONDition]
Function Sets or queries the state of the specified channel
of the specified logic channel for AND triggers.
Syntax
:TRIGger:AND:CHANnel<x>[:
CONDition] {DONTcare|HIGH|LOW|WLIn|
WLOut}
:TRIGger:AND:CHANnel<x>[:CONDition]?
<x> = 1 to 4
Example
:TRIGGER:AND:CHANNEL2:CONDITION HIGH
:TRIGGER:AND:CHANNEL2:CONDITION?
-> :TRIGGER:AND:CHANNEL2:
CONDITION HIGH
Description Use this command on channels that do not have
sub channels.
:TRIGger:AND:CHANnel<x1>:SCHannel<x2
>[:CONDition]
Function Sets or queries the state of the specified sub
channel of the specified logic channel for AND
triggers.
Syntax
:TRIGger:AND:CHANnel<x1>:
SCHannel<x2>[:CONDition] {DONTcare|
HIGH|LOW|WLIn|WLOut}
:TRIGger:AND:CHANnel<x1>:
SCHannel<x2>[:CONDition]?
<x1> = 1 to 4, 7
<x2> = 1 to 60 (sub channel)
Example
:TRIGGER:AND:CHANNEL3:SCHANNEL1:
CONDITION HIGH
:TRIGGER:AND:CHANNEL3:SCHANNEL1:
CONDITION?
-> :TRIGGER:AND:CHANNEL3:SCHANNEL1:
CONDITION HIGH
Description Use this command on channels that have sub
channels.
:TRIGger:ATRigger?
Function Queries all condition A settings.
Syntax
:TRIGger:ATRigger?
:TRIGger:ATRigger:CHANnel<x1>:BIT
<x2>
Function Sets or queries the state of the specified bit of the
specified logic channel of condition A.
Syntax
:TRIGger:ATRigger:CHANnel<x1>:
BIT<x2> {DONTcare|HIGH|LOW}
:TRIGger:ATRigger:CHANnel<x1>:
BIT<x2>?
<x1> = 1 to 6
<x2> = 1 to 8
Example
:TRIGGER:ATRIGGER:CHANNEL5:BIT1 HIGH
:TRIGGER:ATRIGGER:CHANNEL5:BIT1?
-> :TRIGGER:ATRIGGER:CHANNEL5:
BIT1 HIGH
:TRIGger:ATRigger:CHANnel<x1>:SCHann
el<x2>:BIT<x3>
Function Sets or queries the state of the specified bit of
the specified sub channel of the specified logic
channel of condition A.
Syntax
:TRIGger:ATRigger:CHANnel<x1>:
SCHannel<x2>:BIT<x3> {DONTcare|HIGH|
LOW}
:TRIGger:ATRigger:CHANnel<x1>:
SCHannel<x2>:BIT<x3>?
<x1> = 1 to 4, 7
<x2> = 1 to 60 (sub channel)
<x3> = 1 to 8
Example
:TRIGGER:ATRIGGER:CHANNEL1:
SCHANNEL1:BIT1 LOW
:TRIGGER:ATRIGGER:CHANNEL1:
SCHANNEL1:BIT1?
-> :TRIGGER:ATRIGGER
:CHANNEL1:SCHANNEL1:BIT1 LOW
4.33 TRIGger Group