YOKOGAWA DL350 - Page 80

4-53
IM DL350-17EN
Commands
1
2
3
4
5
App
Index
:CHANnel<x>:FREQ:SETup:FILTer:SMOoth
ing:MODE
Function Sets or queries whether smoothing is turned on
for a frequency module.
Syntax
:CHANnel<x>:FREQ:SETup:FILTer:
SMOothing:MODE {<Boolean>}
:CHANnel<x>:FREQ:SETup:FILTer:
SMOothing:MODE?
<x> = 1 to 4
Example
:CHANNEL1:FREQ:SETUP:FILTER:
SMOOTHING:MODE ON
:CHANNEL1:FREQ:SETUP:FILTER:
SMOOTHING:MODE?
-> :CHANNEL1:FREQ:SETUP:FILTER:
SMOOTHING:MODE 1
:CHANnel<x>:FREQ:SETup:FILTer:SMOoth
ing:VALue
Function Sets or queries the moving average order of
smoothing of a frequency module.
Syntax
:CHANnel<x>:FREQ:SETup:FILTer:
SMOothing:VALue {<Time>}
:CHANnel<x>:FREQ:SETup:FILTer:
SMOothing:VALue?
<x> = 1 to 4
<Time> = 0ms to 1000.0ms
Example
:CHANNEL1:FREQ:SETUP:FILTER:
SMOOTHING:VALUE 0.1
:CHANNEL1:FREQ:SETUP:FILTER:
SMOOTHING:VALUE?
-> :CHANNEL1:FREQ:SETUP:FILTER:
SMOOTHING:VALUE 0.1000
:CHANnel<x>:FREQ:SETup:FUNCtion
Function Sets or queries the measurement mode of a
frequency module.
Syntax
:CHANnel<x>:FREQ:SETup:
FUNCtion {DUTY|FREQuency|PERiod|
PFReq|PINTeg|PWIDth|RPM|RPS|
VELocity}
:CHANnel<x>:FREQ:SETup:FUNCtion?
<x> = 1 to 4
Example
:CHANNEL1:FREQ:SETUP:
FUNCTION FREQUENCY
:CHANNEL1:FREQ:SETUP:
FUNCTION FREQUENCY?
-> :CHANNEL1:FREQ:SETUP:
FUNCTION FREQUENCY
Description Table of settings and commands (parameters)
Value Parameter
Duty ratio (Duty)
DUTY
Frequency (Frequency)
FREQuency
Period (Period)
PERiod
Power frequency (Power Freq.)
PFReq
Pulse integration (Pulse Integ)
PINTeg
Pulse width (Pulse Width)
PWIDth
Revolution (rpm) (Revolution(rpm))
RPM
Revolution (rps) (Revolution(rps))
RPS
Velocity (Velocity)
VELocity
:CHANnel<x>:FREQ:SETup:LRESet
Function Sets or queries the over-limit reset when
performing integration measurement on a
frequency module.
Syntax
:CHANnel<x>:FREQ:SETup:
LRESet {<Boolean>}
:CHANnel<x>:FREQ:SETup:LRESet?
<x> = 1 to 4
Example
:CHANNEL1:FREQ:SETUP:LRESET ON
:CHANNEL1:FREQ:SETUP:LRESET?
-> :CHANNEL1:FREQ:SETUP:LRESET 1
:CHANnel<x>:FREQ:SETup:MPULse
Function Sets or queries the positive/negative setting when
measuring pulse width on a frequency module.
Syntax
:CHANnel<x>:FREQ:SETup:
MPULse {POSitive|NEGative}
:CHANnel<x>:FREQ:SETup:MPULse?
<x> = 1 to 4
Example
:CHANNEL1:FREQ:SETUP:MPULSE POSITIVE
:CHANNEL1:FREQ:SETUP:MPULSE?
-> :CHANNEL1:FREQ:SETUP:
MPULSE POSITIVE
4.6 CHANnel Group