YOKOGAWA DL350 - Page 79

4-52
IM DL350-17EN
:CHANnel<x>:FREQ:SETup?
Function Queries all the FV settings of a frequency
module.
Syntax
:CHANnel<x>:FREQ:SETup?
<x> = 1 to 4
:CHANnel<x>:FREQ:SETup:CFRequency
Function Sets or queries the center frequency when
measuring the power frequency on a frequency
module.
Syntax
:CHANnel<x>:FREQ:SETup:
CFRequency {<Frequency>}
:CHANnel<x>:FREQ:SETup:CFRequency?
<x> = 1 to 4
<Frequency> = 50Hz, 60Hz, 400Hz
Example
:CHANNEL1:FREQ:SETup:CFRequency 60
:CHANNEL1:FREQ:SETup:CFRequency?
-> :CHANnel<x>:FREQ:SETup:
CFRequency 60
:CHANnel<x>:FREQ:SETup:DECeleration
Function Sets or queries whether deceleration prediction is
turned on for a frequency module.
Syntax
:CHANnel<x>:FREQ:SETup:
DECeleration {<Boolean>}
:CHANnel<x>:FREQ:SETup:DECeleration?
<x> = 1 to 4
Example
:CHANNEL1:FREQ:SETUP:DECELERATION ON
:CHANNEL1:FREQ:SETUP:DECELERATION?
-> :CHANNEL1:FREQ:SETUP:
DECELERATION 1
:CHANnel<x>:FREQ:SETup:DPULse
Function Sets or queries the distance per pulse when
measuring velocity on a frequency module.
Syntax
:CHANnel<x>:FREQ:SETup:
DPULse {<NRf>}
:CHANnel<x>:FREQ:SETup:DPULse?
<x> = 1 to 4
 <NRf>=9.9999E+30to−9.9999E+30
Example
:CHANNEL1:FREQ:SETUP:
DPULSE 1.00000E+00
:CHANNEL1:FREQ:SETUP:DPULSE?
-> :CHANNEL1:FREQ:SETUP:DPULSE
1.00000E+00
:CHANnel<x>:FREQ:SETup:FILTer?
Function Queries all the filter settings of a frequency
module.
Syntax
:CHANnel<x>:FREQ:SETup:FILTer?
<x> = 1 to 4
:CHANnel<x>:FREQ:SETup:FILTer:PAVera
ge?
Function Queries all the pulse averaging settings of a
frequency module.
Syntax
:CHANnel<x>:FREQ:SETup:FILTer:
PAVerage?
<x> = 1 to 4
:CHANnel<x>:FREQ:SETup:FILTer:PAVera
ge:MODE
Function Sets or queries whether pulse averaging is turned
on for a frequency module.
Syntax
:CHANnel<x>:FREQ:SETup:FILTer:
PAVerage:MODE {<Boolean>}
:CHANnel<x>:FREQ:SETup:FILTer:
PAVerage:MODE?
<x> = 1 to 4
Example
:CHANNEL1:FREQ:SETUP:FILTER:
PAVERAGE:MODE ON
:CHANNEL1:FREQ:SETUP:FILTER:
PAVERAGE:MODE?
-> :CHANNEL1:FREQ:SETUP:FILTER:
PAVERAGE:MODE 1
:CHANnel<x>:FREQ:SETup:FILTer:PAVera
ge:VALue
Function Sets or queries the number of pulses to average
over for a frequency module.
Syntax
:CHANnel<x>:FREQ:SETup:FILTer:
PAVerage:VALue {<NRf>}
:CHANnel<x>:FREQ:SETup:FILTer:
PAVerage:VALue?
<x> = 1 to 4
<NRf> = 1 to 4096
Example
:CHANNEL1:FREQ:SETUP:FILTER:
PAVERAGE:VALUE 2
:CHANNEL1:FREQ:SETUP:FILTER:
PAVERAGE:VALUE?
-> :CHANNEL1:FREQ:SETUP:FILTER:
PAVERAGE:VALUE 2
:CHANnel<x>:FREQ:SETup:FILTer:SMOoth
ing?
Function Queries all the smoothing settings of a frequency
module.
Syntax
:CHANnel<x>:FREQ:SETup:FILTer:
SMOothing?
<x> = 1 to 4
4.6 CHANnel Group