YOKOGAWA UP35A - Program Pattern Setup Charts; IM 05 P02 D41-11 EN Page

IM 05P02D41-11EN page 8/14
3. Program Pattern Setup Charts
Youcanregistermax.10programsegments/patternwiththeUP35Acontroller.Cre-
ate as many copies of the chart as necessary.
System name
ProgramNo.
Programname
Model
SerialNo.
Thefollowingparametersarenecessarytobesetbeforeprogramming.
Notethattheprogramisdeletedif TMUorSEG.T ischangedaftercreating pro-
grams.
Forthesettingrange,see"Parameters."
< Setup Parameters >
Parametersymbol Parameter name Usersettings
TMU Programtimeunit
SEG.T Segmentsettingmethod
ZON ZonePIDselection
Thefollowingparametersarecommonparametersfortheprogrampatternspecied.
Forthesettingrange,see"Parameters."
< Program Pattern Data (common parameter) >
Parametersymbol Parameter name Usersettings
SSP Startingtargetsetpoint
STC Start code
WT.SW1 WaitfunctionON/OFF
WZ.UP1 Upper-sidewaitzone
WZ.LO1 Lower-sidewaitzone
WT.TM1 Waittime
R.CYCL Numberofrepeatcycles
R.STRT Repeatcyclestartsegmentnumber
R.END Repeatcycleendsegmentnumber
Error Indication at Program Pattern Creation and Editing
Errorcode Errorinformation Causeoferror
ERR01
Patterncreationorediting
isdisableduringprogram
or local operation.
Deletingorcopyingoftheprogrampattern,orinserting
ordeletingofthesegmentwasexecutedduringprogram
operation.
ERR22 Segmentwriteerror
Thetotalnumberofsegmentsexceeded20(40whenthe
option“/AP”isspecied.)
ERR23 Segmentinserterror
Newsegmentcannotbeinsertedbecausethenumberof
segmentsinapatternexceeded20(40whentheoption
“/AP”isspecied.)
ERR32
Pattern source
specicationerror
Nopatternexistsinthesource.
ERR33
Pattern destination
specicationerror
Patternsalreadyexistinthedestination.
ERR41 Pattern delete error Thepatterntobedeleteddoesnotexist.
Excepttheaboveerrors,therearesomeerrorcodesincommunication.Fordetails,
seeUser'sManual.
< Program Pattern Data (parameters for segments) >
MaximumvalueofPVinputrange/MaximumvalueofPVinputscale ()
Unit()
Aprogrampatterncanbedrawnintherighttable.
MinimumvalueofPVinputrange/MinimumvalueofPVinputscale ()
Parameter
symbol
Parameter name
Segments
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
TSP Finaltargetsetpoint
TIME Segmenttimesetting
TM.RT Segmentramp-ratesetting
S.PID SegmentPIDnumberselection
JC Junction code
PV.TY1 PVevent-1type
PV.EV1 PVevent-1setpoint
PV.TY2 PVevent-2type
PV.EV2 PVevent-2setpoint
TME1 Startconditionoftimeevent1
T.ON1 Ontimeoftimeevent1
T.OF1 Offtimeoftimeevent1
TME2 Startconditionoftimeevent2
T.ON2 Ontimeoftimeevent2
T.OF2 Offtimeoftimeevent2
TME3 Startconditionoftimeevent3
T.ON3 Ontimeoftimeevent3
T.OF3 Offtimeoftimeevent3
TME4 Startconditionoftimeevent4
T.ON4 Ontimeoftimeevent4
T.OF4 Offtimeoftimeevent4