Home
ABB
Circuit breakers
Emax 2
ABB Emax 2 Installation And Maintenance Guide
5
of 1
of 1 rating
60 pages
Give review
Manual
Specs
To Next Page
To Next Page
To Previous Page
To Previous Page
Loading...
18|
© 20
20 Emax
2
Retr
ofill
Circ
uit
Brea
kers 60
0A-400
0A
2TSA4510
11P00
00 R
ev-B
Figure 43
Figure 44
Figure 45
AKD
5
–
600A
AKD5
–
1600
A
/ 200
0A
AKD
5 – 300
0A / 40
00A
17
19
Table of Contents
Default Chapter
2
Table of Contents
2
Contents
2
1 Hazards
3
Preface
3
2 Warranty
4
3 Trademarks and Patents
5
4 Standards
5
5 Document Conventions
5
6 Related Publications
5
7 Service and Support
6
History and Types
8
8 Estimated Time to Complete Tasks
6
9 Product Specs
6
10 History of AKD
8
Akd - 5, Retrofill Breaker
10
11 AKD-5, Breaker Models
10
12 AKD5 Mechanical Drawings
15
13 Turn OFF/OPEN the Legacy Circuit Breaker
17
14 Rack out Legacy Circuit Breaker
17
15 Empty Compartment Legacy Breaker Removed
17
Modify Akd-5, Switchgear Compartment
17
16 Check, Clean and Grease Compartment
19
Unpack Retrofill Circuit Breaker
20
17 Quality
21
18 Information Label
21
19 Product and Catalog Serial Numbers
21
20 Remove Circuit Breaker from Container
21
Store Circuit Breaker
23
Check before Installing
24
Clean and Grease Breaker
25
Customize Retrofill Secondary Wiring
26
Install Position Switch Actuator, Akt Breaker Retrofill Only
27
Cabinet Only)
28
Racking-Lock Bracket Installation
28
Install Cassette (Landed Wires)
29
Install Cassette Rail Lever Lockout Brackets Ak/Akt50 Compt's Only
32
Install Akd5 Retrofill Breaker
33
21 AK/AKT50 Kirkey Interlock
38
22 Secondary Disconnects, Bullets
39
23 Wiring Diagram and Block Info (AK25)
40
24 AK25 Wiring Harness, B Block AK25/50
45
Install Door Interlock Accessory
46
New Door Installation
47
25 AKD-5, Neutral Disconnect Assembly
49
26 AKD-5, Neutral Disconnect Assembly, Bus Compartment
49
Install Akd-5, Neutral Sensing for 4 Wire Ground Fault
49
27 AKD-5, Neutral CT Adapter Upto 5000A
49
28 Procedures
50
29 AKD-5, Multi-Source Ground Fault
51
Ak 75 - 3000A, Fan Control Unit Wiring & Trip Unit Programming Instructions
52
Configuring Ekip Touch, Hi Touch Trip Unit
54
30 Connecting Ekip Touch
54
31 Synchronizing 2K-1 Signalling Modul with the Trip Unit
55
32 Configuring Threshould Currents
56
33 Programing 2K-1 Signaling Contacts Output
57
Contact Readiness Auto Test
58
Other manuals for ABB Emax 2
Instructions
24 pages
Retrofitting Guide
16 pages
Manual
11 pages
Instructional Sheet
27 pages
5
Based on 1 rating
Ask a question
Give review
Questions and Answers:
Need help?
Do you have a question about the ABB Emax 2 and is the answer not in the manual?
Ask a question
ABB Emax 2 Specifications
General
Breaking Capacity
Up to 150 kA
Number of Poles
3 or 4
Standards
IEC 60947-2
Rated insulation voltage
1000V AC
Mounting
Fixed, Withdrawable
Related product manuals
ABB Emax
20 pages
ABB SACE Emax
15 pages
ABB Emax Series
10 pages
ABB SACE Emax 2
109 pages
ABB SACE Emax E1
2 pages
ABB SACE Emax E1.2
311 pages
ABB SACE Emax E2.2
311 pages
ABB SACE Emax Series
161 pages
ABB SACE Emax 2 E6.2
56 pages
ABB SACE Emax E4.2-A
77 pages
ABB Emax 2 IEC 60947
30 pages
ABB SACE Emax 2 Series
302 pages
Need help?
General
To Next Page
