ABB HT595584 - Page 143

Operation Manual / 4 Product description / A100-M axial
Tables
© Copyright 2019 ABB. All rights reserved. HZTL4033_EN Revision D December 2019
Tables
Table1: Related documents .......................................... 3
Table2: Weight of complete turbocharger unit....... 8
Table3: Foot screws, dimension and strength class..
14
Table4: Foot screws, dimension CE.......................... 14
Table5: Foot screws, dimension TE.......................... 14
Table6: Foot screws, number of cup springs ......... 15
Table7: Torque-controlled tightening of the pres-
sure screws .................................................................... 18
Table8: Oil pressure range.......................................... 22
Table9: Oil temperature at the inlet ......................... 23
Table10: Oil temperature at the outlet .................... 23
Table11: Expected replacement intervals ................ 33
Table12: Recommended replacement intervals ..... 33
Table13: Tightening torque (81272) .......................... 37
Table14: Tightening torque (81273).......................... 37
Table15: Compressor cleaning parameters ............ 41
Table16: Compressor cleaning parameters ........... 44
Table17: Cleaning parameters Wet cleaning of tur-
bine and nozzle ring..................................................... 50
Table18: Malfunctions when starting – Delayed
start-up ........................................................................... 51
Table19: Malfunctions when starting – Vibrations 51
Table20: Malfunctions when starting – Rubbing of
rotating parts................................................................. 51
Table21: Malfunctions during operation – Lubricat-
ing oil pressure too low............................................... 52
Table22: Malfunctions during operation – Drop in
speed .............................................................................. 52
Table23: Malfunctions during operation – Speed in-
creases ........................................................................... 52
Table24: Malfunctions during operation – Exhaust
gas temperature too high .......................................... 53
Table25: Malfunctions during operation – Charge air
pressure too low........................................................... 53
Table26: Malfunctions during operation – Charge air
pressure too high ......................................................... 54
Table27: Surging of the turbocharger..................... 54
Table28: Malfunctions when stopping – Runout
noises............................................................................... 55
Table29: Malfunctions when stopping – Shortened
runout time ..................................................................... 55
Table30: Malfunction, No speed measurement sig-
nal or poor signal amplitude ....................................... 56
Table31: Malfunction, Measured speed too high ... 56
Table32: Malfunction, Measured speed too low..... 56
Table33: Assembly weights ........................................ 59
Table34: Axial clearance A........................................... 62
Table35: Tightening torque (56014) ......................... 74
Table36: Tightening torque (57005)......................... 75
Table37: Tightening torque (61069) ......................... 77
Table38: Tightening torque (61059 / 42128)........... 79
Table39: Tightening torque(86505)......................... 80
Table40: Inner thread size (25008) ........................... 81
Table41: Tightening torque (25013).......................... 82
Table42: Tightening torque (61037).......................... 83
Table43: Tightening torque, nuts that are difficult
to access (61037) ........................................................... 83
Table44: Tightening torque (61090)......................... 83
Table45: Tightening torque (77015).......................... 84
Table46: Tightening torque (72011).......................... 86
Table47: Axial clearance A ........................................... 87
Table48: Tightening torque (27027) ......................... 88
Table49: Tightening torque (27027) ......................... 89
Table50: Tightening torque (56014)......................... 92
Table51: Tightening torque (61009) ......................... 93
Table52: Tightening torques ...................................... 95
Table53: Tightening torques 61009.......................... 96
Table54: Locking device tightening torque ............ 99
Table55: Cover plate dimensions 1 ......................... 101
Table56: Cover plate dimensions 2 ......................... 101
Table57: Cover plate dimensions 3 ......................... 101
Table58: Customer spare part set (97070)............ 108
Page 113 / 114Page 113 / 114