ABB TTF300 - HART Parameter Overview (SW-Rev. 01.03) - Calibrate;Diagnosis

92 pages

To Next Page

To Previous Page

TTF300 FIELD-MOUNT TEMPERATURE TRANSMITTER | OI/TTF300-EN REV. I 53

Calibrate

Measured range

Apply Lower Range

Apply Upper Range

Analog Out

Trim 4 mA

Trim 20 mA

Diagnosis

Looptest

Device status

Temp. of Electronics

Sensor 1 process data

Sensor 2 process data

Main Page

Table of Contents2
Safety4
General Information and Instructions4
Warnings4
Intended Use5
Improper Use5
Warranty Provisions5
Cyber Security Disclaimer5
Software Downloads5
Manufacturer's Address5
Service Address5
Use in Potentially Explosive Atmospheres in Accordance with ATEX and Iecex6
Ex Marking6
Transmitter6
LCD Indicator7
Temperature Data8
Transmitter8
LCD Indicator8
Electrical Data8
LCD Indicator9
Installation Instructions10
ATEX / Iecex / EAC-Ex10
Cable Entries10
Electrical Connections11
Commissioning16
Operating Instructions17
Damage to the 'Flameproof (Enclosure)- Ex D' Type of Protection17
Protection against Electrostatic Discharges17
Repair17
Use in Potentially Explosive Atmospheres in Accordance with Cfmus, FM and CSA18
Transmitter Ex Marking Cfmus18
Transmitter Ex Marking FM / CSA18
LCD Indicator Ex Marking19
Installation Instructions20
Electrical Connections20
Commissioning20
Operating Instructions20
Adverse Effect on the 'Explosionproof - XP' Type of Protection20
Protection against Electrostatic Discharges20
Repair21
Design and Function22
Input Functionality22
Sensor Redundancy22
Sensor Drift Monitoring24
Sensor Error Adjustment in Accordance with Callendar-Van Dusen24
Product Identification25
Name Plate25
Explosion Protection Marking for Devices with One Type of Protection25
Explosion Protection Marking for Devices with Several26
Types of Protection26
Transport and Storage27
Inspection27
Transporting the Device27
Storing the Device27
Ambient Conditions27
Returning Devices27
Installation27
Mounting28
Opening and Closing the Housing28
Rotating the LCD Indicator29
Electrical Connections29
Safety Instructions29
Protection of the Transmitter from Damage Caused by Highly Energetic Electrical Interferences30
Suitable Protective Measures30
Conductor Material30
Power Supply Cable30
Cable Glands30
Shielding of the Sensor Connecting Cable31
Recommended Shielding / Grounding31
Additional Examples for Shielding / Grounding32
Terminal Assignment34
Resistance Thermometers (RTD) / Resistors (Potentiometer)34
Thermocouples / Voltages and Resistance35
Thermometers (RTD) / Thermocouple Combinations35
Terminal for Sensor Connection Cable36
Electrical Data for Inputs and Outputs37
Input - Resistance Thermometer / Resistances37
Input - Thermocouples / Voltages37
Functionality Input37
Output - HART38
Output - PROFIBUS PA38
Output - FOUNDATION Fieldbus39
Power Supply39
Power Supply - HART39
Power Supply - PROFIBUS / FOUNDATION Fieldbus40
Commissioning41
General41
Checks Prior to Commissioning41
Communication41
HART® Communication41
PROFIBUS® Communication42
FOUNDATION Fieldbus® Communication43
Basic Setup43
10 Operation44
Safety Instructions44
Hardware Settings44
Devices with HART® from HW-Rev.: 02.00 (Corresponds to Software from SW-Rev.: 03.00 and Higher)44
Devices with PROFIBUS PA®, FOUNDATION Fieldbus®, and HART® to HW-Rev.: 01.0744
Menu Navigation45
HART® Menu Levels46
To SW-Rev.: 01.0346
From SW-Rev.: 03.0046
PROFIBUS PA® and FOUNDATION Fieldbus® H1 Menu Levels47
Process Display48
Error Messages in the HART® LCD Display48
Error Messages in the PROFIBUS PA® and FOUNDATION Fieldbus® LCD Display49
Switching to the Information Level50
Selecting and Changing Parameters51
Entry from Table51
Numerical Entry51
Alphanumeric Entry51
Parameter Overview HART® (for Devices to SW-Rev.: 01.03)52
Parameter Description HART® (for HART®-Devices to SW-Rev.: 01.03)54
Menu: Device Setup54
Menu: Device Info57
Menu: Display57
Menu: Process Alarm58
Menu: Communication58
Menu: Calibrate58
Menu: Diagnosis59
Activating Write Protection59
Deactivating Write Protection59
Parameter Overview HART® (for HART-Devices from SW-Rev.: 03.00)60
Parameter Description HART® (for HART®-Devices from SW-Rev.: 03.00)63
Menu: Easy Setup63
Menu: Device Setup66
Menu: Display68
Menu: Process Alarm68
Menu: Communication69
Menu: Calibrate70
Menu: Diagnosis70
Menu: Device Info71
Menu: Service71
Software Write Protection72
PROFIBUS PA® und FOUNDATION Fieldbus® Parameter Overview73
Parameter Description PROFIBUS PA® and FOUNDATION Fieldbus75
Menu: Device Setup75
Menu: Device Info77
Menu: Communication77
Menu: Service Menu78
Menu: Display79
Menu: Calibrate79
Factory Settings80
Firmware Settings80
11 Diagnosis / Error Messages81
Diagnostic Information81
Monitoring of Operating Data81
Operating Hours Statistics81
Calling up the Error Description82
Possible Error Messages - HART® Devices to SW-Rev.: 01.0383
Possible Error Messages - HART® Devices from SW-Rev.: 03.0085
Possible Error Messages - PROFIBUS PA® and FOUNDATION Fieldbus86
12 Maintenance87
Safety Instructions87
Cleaning87
13 Repair87
Returning Devices87
14 Recycling and Disposal88
15 Specification88
16 Additional Documents88
17 Appendix89
Return Form89

ABB TTF300 - HART Parameter Overview (SW-Rev. 01.03) - Calibrate;Diagnosis

Table of Contents

Other manuals for ABB TTF300

Related product manuals