Operation Manual / 4 Product description / A200-L
Figures
© Copyright 2018 ABB. All rights reserved. HZTL4036_EN Revision M August 2018
Figures
Fig.1: Layout and function of the turbocharger...... 4
Fig.2: Warning plate locations .................................... 6
Fig.3: Locations of the rating plates .......................... 7
Fig.4: Fitting lifting gear to turbocharger................ 9
Fig.5: Placing the turbocharger on the bracket ..... 10
Fig.6: Compressor-end foot....................................... 11
Fig.7: Turbine-end foot................................................ 11
Fig.8: Layout and overview of the speed measure-
ment system................................................................... 18
Fig.9: Replacing the speed sensor ........................... 20
Fig.10: U-tube manometer at the filter silencer..... 21
Fig.11: Noise insulation, bellows................................ 23
Fig.12: Layout and overview of filter silencer ......... 31
Fig.13: Dismantling filter ring circumferential part....
33
Fig.14: Opening filter ring lock................................... 33
Fig.15: Attaching new filter ring ............................... 34
Fig.16: Fitting new filter ring..................................... 34
Fig.17: Overview of wet cleaning of compressor ... 37
Fig.18: Filter plug view................................................ 38
Fig.19: Overview of dry cleaning device .................. 40
Fig.20: Drain pipe diagram ........................................ 43
Fig.21: Overview of assembly weights .................... 52
Fig.22: Overview of filter silencer casing disas-
sembly and assembly .................................................. 53
Fig.23: Fitting filter silencer casing 1....................... 54
Fig.24: Fitting filter silencer casing 2 ...................... 55
Fig.25: Fitting filter silencer casing 3 ...................... 55
Fig.26: Fitting filter silencer casing 4...................... 56
Fig.27: Fitting filter silencer casing 5 ...................... 56
Fig.28: Fitting the bellows .......................................... 57
Fig.29: Dismantling the filter silencer ..................... 58
Fig.30: Dismantling the filter silencer ..................... 59
Fig.31: Pressing off compressor casing.................. 60
Fig.32: Moving out wall insert .................................... 61
Fig.33: Putting down wall insert ................................ 61
Fig.34: Putting down wall insert ................................ 62
Fig.35: Dismantling the diffuser ............................... 63
Fig.36: Measuring axial clearance A .......................... 64
Fig.37: Removing the insulation (A275-L and smal-
ler)..................................................................................... 65
Fig.38: Dismantling the gas inlet casing (A275-L and
smaller) – screwed variant ........................................... 66
Fig.39: Dismantling the gas inlet casing (275-L and
smaller) – threaded stud variant ................................ 67
Fig.40: Dismantling the nozzle ring (A275-L and
smaller) ............................................................................ 68
Fig.41: Dismantling the gas inlet casing (A280-L) –
screwed variant.............................................................. 69
Fig.42: Dismantling the gas inlet casing (A280-L) -
threaded stud variant................................................... 70
Fig.43: Fitting the nozzle ring holder (A280-L) ........ 71
Fig.44: Dismantling the nozzle ring (A280-L).......... 72
Fig.45: Putting down the nozzle ring (A280-L) ....... 72
Fig.46: Fitting the nozzle ring (A275-L and smaller) ...
73
Fig.47: Fitting the gas inlet casing (A275-L and
smaller) - screwed variant............................................ 74
Fig.48: Fitting the gas inlet casing (A275-L and
smaller) - threaded stud variant................................. 75
Fig.49: Fitting the insulation (A275-L and smaller).....
76
Fig.50: Fitting the nozzle ring (A280-L) ................... 77
Fig.51: Attaching the nozzle ring (A280-L) .............. 78
Fig.52: Fitting the gas inlet casing (A280-L) –
screwed variant.............................................................. 79
Fig.53: Fitting the gas inlet casing (A280-L) –
screwed variant.............................................................. 80
Fig.54: Measuring axial clearance A .......................... 81
Fig.55: Fitting the diffuser.......................................... 82
Fig.56: Positioning wall insert.................................... 83
Fig.57: Fitting the wall insert ..................................... 84
Page 106 / 108Page 106 / 108
To Next Page
Loading...
