Operation Manual / A100-L
Figures
© Copyright 2021 ABB. All rights reserved. HZTL4034_EN Revision T December 2021
Figures
Fig.1: Layout and function of the turbocharger...... 6
Fig.2: Locations of the rating plates ......................... 8
Fig.3: Warning plate locations ................................... 13
Fig.4: Rating plate ........................................................ 13
Fig.5: Attachment of loads on the crane hook ....... 16
Fig.6: Attachment angle.............................................. 16
Fig.7: Fitting the lifting gear ..................................... 26
Fig.8: Placing the turbocharger................................. 27
Fig.9: Compressor-end foot...................................... 28
Fig.10: Turbine-end foot ............................................ 28
Fig.11: Oil temperature at the outlet ....................... 34
Fig.12: Layout and overview of the speed measure-
ment system.................................................................. 36
Fig.13: Replacing the speed sensor ......................... 38
Fig.14: U-tube manometer at the filter silencer .... 39
Fig.15: Noise insulation, bellows ............................... 41
Fig.16: Layout and overview of filter silencer ........ 49
Fig.17: Dismantling filter ring circumferential part ....
51
Fig.18: Opening filter ring lock................................... 51
Fig.19: Attaching new filter ring ............................... 52
Fig.20: Fitting new filter ring .................................... 52
Fig.21: Overview of wet cleaning of compressor .. 55
Fig.22: Filter plug view................................................ 56
Fig.23: Dry cleaning device ........................................ 58
Fig.24: Drain pipe diagram ......................................... 61
Fig.25: Weights of assemblies ................................. 70
Fig.26: Dismantling the filter silencer casing ......... 71
Fig.27: Fitting the filter silencer casing ................... 72
Fig.28: Fitting the filter silencer casing .................. 73
Fig.29: Fitting the filter silencer casing .................. 73
Fig.30: Fitting the filter silencer casing .................. 74
Fig.31: Fitting the filter silencer casing................... 74
Fig.32: Fitting the bellows .......................................... 75
Fig.33: Dismantling the filter silencer....................... 76
Fig.34: Dismantling the filter silencer ...................... 77
Fig.35: Dismantling the filter silencer with noise
package ........................................................................... 78
Fig.36: Dismantling the wall insert............................ 79
Fig.37: Moving out wall insert .................................... 80
Fig.38: Putting down wall insert ................................ 80
Fig.39: Putting down wall insert ................................ 81
Fig.40: Dismantling the diffuser ............................... 82
Fig.41: Measuring axial clearance A........................... 83
Fig.42: Removing the insulation (A175-L and smal-
ler)..................................................................................... 84
Fig.43: Dismantling the gas inlet casing (A175-L and
smaller) ............................................................................ 85
Fig.44: Dismantling the nozzle ring (A175-L and
smaller) ............................................................................ 86
Fig.45: Dismantling the gas inlet casing (180-L and
larger)............................................................................... 87
Fig.46: Fitting the nozzle ring holder........................ 88
Fig.47: Dismantling the nozzle ring........................... 89
Fig.48: Put down the nozzle ring ............................... 89
Fig.49: Fitting the nozzle ring (A175-L and smaller) ...
90
Fig.50: Fitting the gas outlet casing (A175-L and
smaller) ............................................................................ 91
Fig.51: Fitting the insulation (A175-L and smaller). 92
Fig.52: Looping around the nozzle ring (A180-L and
larger)............................................................................... 93
Fig.53: Fitting the nozzle ring (A180-L and larger). 94
Fig.54: Fitting the gas inlet casing (A180-L and lar-
ger) ................................................................................... 95
Fig.55: Measuring axial clearance A .......................... 96
Fig.56: Fitting the diffuser.......................................... 97
Fig.57: Positioning wall insert .................................... 98
Fig.58: Fitting wall insert ........................................... 99
Fig.59: Fitting the filter silencer .............................. 101
Fig.60: Fitting the filter silencer .............................. 102
Page 138 / 141Page 138 / 141
To Next Page
Loading...
Need help?
General
