Agilent Technologies 6632B

1 – Quick Reference
14
SCPI Programming Commands - At a Glance
NOTE Some [optional] commands have been omitted for clarity. Refer to the Programming
Guide for a complete description of all programming commands.
ABORt SENSe
CALibrate :CURRent :RANGe <n>
:CURRent [:SOURce] [:POSitive] :DETector ACDC | DC
1
:NEGative :FUNCtion “VOLT” | “CURR”
1
:MEASure :LOWRange :SWEep :OFFSet :POINts <n>
1
:AC
1
:POINts <n>
:DATA <n> :TINTerval <n>
:LEVel P1 | P2 | P3 | P4 :WINDow HANN | RECT
:PASSword <n> [SOURce:]
:SAVE CURRent [:LEVel] [:IMMediate] <n>
:STATe <bool> [, <n>] :TRIGgered <n>
:VOLTage [:DC] :PROTection :STATe <bool>
:PROTection DIGital :DATA <n>
DISPlay :FUNCtion RIDF | DIG
[:STATe] <bool> VOLTage [:LEVel] [:IMMediate] <n>
:MODE NORMal | TEXT :TRIGgered <n>
:TEXT <display_string> :ALC :BANDwidth? | :BWIDth?
INITiate :PROTection <n>
[:IMMediate] :SEQuence[1|2
1
] STATus
:NAME TRANsient | ACQuire
1
:PRESet
:CONTinuous :SEQuence[1], <bool> :OPERation [:EVENt]?
:NAME TRANsient, <bool> :CONDition?
MEASure | FETCh
2
:ENABle <n>
:ARRay :CURRent?
1
:NTRansition <n>
:VOLTage?
1
:PTRansition <n>
[:SCALar]:CURRent[:DC]? :QUEStionable [:EVENt]?
:ACDC?
1
:CONDition?
:HIGH?
1
:ENABle <n>
:LOW?
1
:NTRansition <n>
:MAX?
1
:PTRansition <n>
:MIN?
1
SYSTem
:VOLTage [:DC]? :ERRor?
:ACDC?
1
:LANGuage SCPI | COMPatibility
:HIGH?
1
:VERSion?
:LOW?
1
:LOCal
:MAX?
1
:REMote
:MIN?
1
:RWLock
OUTPut TRIGger
[:STATe] <bool> [,NORelay] :SEQuence2 | :ACQuire [:IMMediate]
1
:DFI [:STATe] <bool> :COUN t :CURRent <n>
1
:SOURce QUES | OPER | ESB | RQS | OFF :VOLTage <n>
1
:PON :STATe RST | RCL0 :HYSTeresis:CURRent <n>
1
:PROTection :CLEar :VOLTage <n>
1
:DELay <n> :LEVel :CURRent <n>
1
:RELay [:STATe] <bool>
3
:VOLTage <n>
1
:POLarity NORM | REV
3
:SLOPe :CURRent POS | NEG | EITH
1
:RI :MODE LATCHing | LIVE | OFF
:VOLTage POS | NEG | EITH
1
:SOURce BUS | INTernal
1
[:SEQuence1 | :TRANsient] [:IMMediate]
1
Not available on Agilent 6631B - 6634B :SOURce BUS
2
Fetch commands not available on Agilent 6631B – 6634B :SEQuence1 :DEFine TRANsient
3
Not available on Agilent 6631B :SEQuence2 :DEFine ACQuire
1