EasyManua.ls Logo

Agilent Technologies TriScroll 800 - User Manual

Agilent Technologies TriScroll 800
32 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
INSTALLATION AND
OPERATION MANUAL
Vacuum Products Division
DRA
FT 10/9/14
TriScroll
TM
800
Inverter Dry Scroll
Vacuum Pump
Manual No. 699904435
Revision B
October 2014

Table of Contents

Questions and Answers

  • K
    Kerry DavenportAug 14, 2025
    What to do if my Agilent Technologies Water Pump has poor ultimate pressure?
    • M
      Mr. Tyrone MeyerAug 14, 2025
      If your Agilent Technologies Water Pump has poor ultimate pressure, there are several potential causes. Check for system leaks and repair them. If there is water or solvent in the pump, flush it with air or dry nitrogen. If solvent is the issue, consider installing a trap or filter. A plugged gas ballast can also cause this problem, in which case you should replace the breather vent. Worn out seals can also lead to poor pressure, so replace the tip seals. Lastly, ensure there isn't poor conductance to the pump by replumbing with shorter or larger diameter tubing.
  • T
    Tamara HansenAug 25, 2025
    How to fix a hammering noise in my Agilent Technologies Water Pump?
    • P
      Pamela WareAug 26, 2025
      If your Agilent Technologies Water Pump is making a hammering noise, it could be due to the pump overheating. Check the ambient temperature and ensure adequate ventilation to the pump. Another possible cause is debris in the pump. Inspect the inlet screen, flush the pump to remove any debris.
  • M
    Marvin AndradeNov 3, 2025
    Why won't my Agilent Technologies TriScroll 800 start?
    • R
      Robert WashingtonNov 3, 2025
      If the Agilent Technologies Water Pump won't start, several issues could be the cause. First, ensure the P1 interlock connector is plugged in and the TPS cable is properly connected. Verify that the inverter is plugged into a 200-240 VAC 50/60 Hz power source. Check if the circuit breaker is open and close it, identifying any overload causes. Also, ensure the motor thermal protector isn't open by allowing the motor to cool and identifying any overload causes. Inspect the main fuse and replace it if necessary with a Type H, 10 A, 250 V fuse. Check for any loose or cut wiring and repair or replace them. Excessive voltage drop can also prevent the pump from starting, so check the size and length of the power supply cable. If none of these steps work, the motor may be defective, requiring insp...

Summary

Warranty Information

Warranty Claims and Adjustments

Procedures for making warranty claims, including product return and seller responsibilities.

Instructions for Use

General Information

Overview of the pump's purpose, intended use, and safety protocols.

Unpacking and Inspection

Steps for safely unpacking and inspecting the pump for any shipping damage.

Storage Requirements

Environmental requirements for storing the vacuum pump to prevent damage.

Installation Requirements

Safety Precautions

Key safety warnings and precautions to prevent injury and equipment damage.

Environmental Conditions

Guidelines for operating the pump within specified temperature and humidity limits.

Power and Electrical Setup

Power Cord and Extension Cords

Details on power cord selection and recommendations for using extension cords safely.

Circuit Breakers and Grounding

Information on circuit breakers and proper grounding for pump safety.

Mechanical Connections

Pump Location and Valves

Guidance on pump location and the operation of the vacuum pump isolation valve.

Inlet, Exhaust, Gas Ballast, Bearing Purge

Details on pump inlet, exhaust, gas ballast, and bearing purge port configurations.

Operation Procedures

Startup and Shutdown

Step-by-step instructions for safely starting up and shutting down the vacuum pump.

Maintenance Overview

Maintenance Safety Precautions

General information and safety precautions regarding pump maintenance.

Technical Information

Pump Specifications

Detailed specifications for the TriScroll 800 Inverter vacuum pump.

Pump Electrical Controller

Controller Specs and Interlocks

Technical details for the controller, including specifications and P1 I/O-1 interlock.

Driving Frequency Control

Graph showing the relationship between analog input voltage and pump driving frequency.

Serial Interface Specification

J1 Serial Port and P2 Connector

Pinout details for the J1 serial port and P2 I/O-2 DB9 connector.

T-Plus Software Operation

Status LEDs and Frequency Adjustment

Understanding status LEDs and adjusting target frequency using T-Plus software.

Accessories and Kits

Purge, Silencer, Vibration Isolation, HEPA Filter

Details on various accessories like purge kits, silencers, isolation mounts, and HEPA filters.

Troubleshooting

Troubleshooting Chart

A chart listing common problems, their causes, and corrective actions for the pump.

Maintenance Procedures

General Maintenance and Related Manuals

Guidelines for maintenance and references to other relevant technical manuals.

Maintenance and Tooling Kits

Information on maintenance kits and tooling required for pump upkeep.

Service and Support

Factory Service Options and Accessories

Overview of factory service options and available accessories for the pump.

Contacting Agilent

Information on how to contact Agilent for customer service and support.

Product Returns Process

Return Instructions and Forms

Detailed instructions on product returns, including necessary forms and procedures.

Global Support Locations

Regional Contact Information

Contact details for Agilent's Vacuum Products Division across various global regions.

Agilent Technologies TriScroll 800 Specifications

General IconGeneral
BrandAgilent Technologies
ModelTriScroll 800
CategoryWater Pump
LanguageEnglish

Related product manuals