To enter, press the START (enter) keypad. The display will show
iC XX where XX is the software version of the drive.
To exit the test, simultaneously press the SELECT (∧) and DIS-
PLAY (∨) keypads. The control will return to the Manual Diag-
nostic Mode Menu.
Service Door Switch Input Test d 08
This option tests the service door switch. To start test, control
must be in the Manual Diagnostic Mode Menu.
To enter, press the START (enter) keypad. The display will show
S oP when the service door switch is open and S CL when the
service door switch is closed.
The service door switch has to be closed for at least one second
and opened for at least one second for the display to change. This
test will add a count to the service door opening counter for the
audit and save the date/time for each opening.
To exit the test, simultaneously press the SELECT (∧) and DIS-
PLAY (∨) keypads. The control will return to the Manual Diag-
nostic Mode Menu.
Dryer on Temperature Test d 14
This option tests the temperature inside the cylinder while run-
ning a cycle. To start test, control must be in the Manual Diag-
nostic Mode Menu.
To enter, press the START (enter) keypad. The machine will run
until it has reached the selected cycle temperature. The display
will show XX XF for degrees in Fahrenheit or XX XC for de-
grees in Celsius. The XX X will show the degrees. During cool
down, the control will display the time remaining as NN (minutes)
or NN SS (minutes and seconds).
To exit the test, simultaneously press the SELECT (∧) and DIS-
PLAY (∨) keypads. The control will return to the Manual Diag-
nostic Mode Menu.
Door Switch Input Test d 15
This test will display whether the loading door is open or closed.
To start test, control must be in the Manual Diagnostic Mode
Menu.
To enter, press the START (enter) keypad. If the door is open, the
display will show dr oP. If the door is closed, the display will
show dr CL.
To exit the test, simultaneously press the SELECT (∧) and DIS-
PLAY (∨) keypads. The control will return to the Manual Diag-
nostic Mode Menu.
Lint Door Switch Input Test d 16
This test will display whether the lint door switch is open or
closed. To start test, control must be in the Manual Diagnostic
Mode Menu.
To enter, press the START (enter) keypad. If the lint door switch
is open, the display will show Lt oP. If the lint door switch is
closed, the display will show Lt CL.
To exit the test, simultaneously press the SELECT (∧) and DIS-
PLAY (∨) keypads. The control will return to the Manual Diag-
nostic Mode Menu.
Temperature Sensor Display Test d 19
This option displays the temperature sensed at the thermistor. To
start test, control must be in the Manual Diagnostic Mode Menu.
To enter, press the START (enter) keypad. If the door is closed,
the display will show XX XF or XX XC. The F will show Fah-
renheit, the C will show Celsius and the XXX will show degrees.
If control senses a shorted thermistor, the display will show SH. If
the control senses an open thermistor, the display will show oP.
To exit the test, simultaneously press the SELECT (∧) and DIS-
PLAY (∨) keypads. The control will return to the Manual Diag-
nostic Mode Menu.
12.5VDC Voltage Test d 20
This test displays the value of the 12.5VDC supply. To start test,
control must be in the Manual Diagnostic Mode Menu.
To enter, press the START (enter) keypad. The display will show
XX XX where XXX is the voltage.
To exit the test, simultaneously press the SELECT (∧) and DIS-
PLAY (∨) keypads. The control will return to the Manual Diag-
nostic Mode Menu.
24VDC Voltage Test d 21
This test will display whether the washer door is open or closed.
To start test, control must be in the Manual Diagnostic Mode
Menu.
To enter, press the START (enter) keypad. The display will show
XX XX where XXX in the voltage. The 24V supply is charged
when the door is closed. If the door is open the supply will dis-
charge to a near zero (0) value.
To exit the test, simultaneously press the SELECT (∧) and DIS-
PLAY (∨) keypads. The control will return to the Manual Diag-
nostic Mode Menu.
AC Mains Voltage Test d 28
This will display the AC Mains Voltage. To start test, control
must be in the Manual Diagnostic Mode Menu.
To enter, press the START (enter) keypad. The display will show
XXX which is the voltage in 1 Volt precision.
To exit the test, simultaneously press the SELECT (∧) and DIS-
PLAY (∨) keypads.
Machine Diagnostic Functions
©
Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
35 Part No. 70579901ENR9
To Next Page
Loading...
