EasyManuals Logo

Alpine CDA-9886M User Manual

Alpine CDA-9886M
80 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #15 background imageLoading...
Page #15 background image
Sound Setting
Setting
the
Subwoofer
level
Adjusting
Subwoofer
level/Bass
level/
Treble
level/Balance
(Between
left
and
Right)/Fader
(Between
Front
and
Rear)/
Defeat
/{no
operation is
perfonlledfor
/5
sewlU!s. the lmit will rerum
ro
1I0rmaimode automatically.
" When the subwoo{er mode is set to
OFF.
irs
lel'el ClInnot be adjusted.
Re{er to "Turning Subwo(}/er
ON/OFF"
(page 16).
The adjustment
CUll
also
be
made by pressillg Rotary
encoder
(AUDIO). Reler to "Adjusting Subwo(}/er Level/Bass Level/Treble
Level/Balance (Between
Le./i
and Right)/Fader (Betweell Front
and
Rear)/De./eat" (page /4).
*2
The./imction is inoperable when DEFEATis set
to
ON.
You
can change the Subwoofer Level to create your own tonal
preference,
1 Press
SOUND
SETUP
to
activate the Sound Setting
mode.
2 Turn the
Rotary
encoder
to select the SUBW. Level
Adjustment mode, and then
press"
lENT.
SUBW Level*t H Bass*2 H
Treble
2
H
HPF*2
H Black Out
H SUBW Level
3 Turn the
Rotary
encoder
to select the desired
subwoofer level (0-+15).
,I
"T
L
"t
i
.
SOUND
SETUP
:;
~/ESC
SOURCElc!>
Rotary
encoder
(AUDIO·LOUD)
r
.IBAC..~
..
~~T
i
66
[J[]:
i
[J[j,,'--
:_~
'.
1 Press
Rotary
encoder
(AUDIO)
repeatedly to
choose the desired mode.
Setting
the
Bass
Control
Each press
changes
the
mode
as follows:
SUBWOOFER*
~
BASS
~
TREBLE
~
BALANCE
~
FADER
~
DEFEAT
~
VOLUME
~
SUBWOOFER
Subwoofer level: 0 - +
15
Bass level:
-7
- +7
Treble level:
-7
- +7
Balance: L
15
-
R15
Fader:
R15
-
F15
Defeat: ON/OFF
Volume: 0 -
35
You
can change the Bass Frequency emphasis to create your own tonal
preference.
1 Press
SOUND
SETUP
to activate the Sound Setting
mode.
2 Turn the
Rotary
encoder
to select the Bass
Adjustment mode, and then press
"lENT.
SUBW Level,3 H Bass*4 H Treble*4 H
HPF*4
H Black
Out
H SUBW Level
1{1I0
operatioll is
performedfor
5 secollds alier selectillg the
SUBWOOFER, BASS, TREBLE. BALANCE. FADER. VOLUME
or
DEFEAT
II/ode,
the ullit autoll/atically retul'lls to 1I0rmai mode.
* Whell the subwoo{er mode is set to
OFF.
its level call1lot be adjusted.
Refer to "Turnillg Subwo(}fer
ON/OFF"
(page /6).
2
Turn
the
Rotary
encoder
until the desired sound
is
obtained
in
each mode.
By
setting Defeat ON, previously adjusted settings of BASS
and TREBLE will return to the factory defaults.
setth~~tl1e.~~SS
C!h!er
Frequency
3-1
Press
BAND
to select the desired bass center
frequency.
80 Hz
~
100
Hz
~
200
Hz
~
60
Hz
~
80
Hz
Emphasizes the displayed bass frequency ranges.
$etting:the Bass Bandwidth
Depelldillg
011
the collllected devices. some
limctions
alld display
illdications do not work.
3-2
Press SOURCE/c!> to select the desired bass
bandwidth.
Changes the boosted bass
bandwidth
to
wide
or narrow. A
wider
setting will boost a
wide
range of frequencies above
and below the center frequency. A narrower setting will
boost only frequencies near the center frequency.
14-EN

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Alpine CDA-9886M and is the answer not in the manual?

Alpine CDA-9886M Specifications

General IconGeneral
BrandAlpine
ModelCDA-9886M
CategoryCar Receiver
LanguageEnglish

Related product manuals