Adjusting
Subwoofer
Level/Bass
Level/
Treble
Level/Fader
(Between
Front
and
Rear)/Balance
(Between
Left
and
Right)/
Black
Out
in
MullED
mode
You
can change these settings to create your own preference
in
MultEQ
(Curve I or Curve 2) mode.
1 Press
IMPRINT
to activate the MultEQ adjustment
mode.
2 Turn the
Rotary
encoder
to select the desired item,
and then press
~IENT.
SUBW
Level*'
H Bass Level H Treble Level H Fader*2 H
Balance H Black Out*J H SUBW Level
3 Turn the
Rotary
encoder
to change the setting as
below, and then press
~
lENT.
Subwoofer level: a - +
15
Bass level:
-7-+7
Treble level:
-7-+7
Fader:
R15
- F15
Balance: L15 - R15
Black Out: ON/OFF
•
Ifno
operaTion is
performed/or
60
seconds
alier
selecTing
The
SUBW
Level. Bass Level. Treble Level.
Fader.
Balance
or
Black
Ol/T
mode,
The
unit automatically retl/ms
To
normal mode.
*1
When the subwoot'er
mode
is set
To
OFF, its level cannot
be
adjl/sted,
and
the
suhwoofer
ON/OFF
cannot
be
adjl/sted in MultEQ (Curve I
or
CI/n'e 2) mode.
*2
If
you set the 2.2ch (3WAY)/4.2ch (FRONT/REARJSUBW) switch
of
the
IMPRINT
al/dio processor (PXA-HlOO) to 2.2ch (3WAY).
you
cannot adjl/st the FADER mode. For details. refer to the
Owner's
Manual
of
PXA
-H
1.00.
*J
When Blackout mode is
tl/med
on. all display indications on this
I/niT
will
tum
off
to redl/ce
power
consl/mpTion. This addiTional
power
enhances the
sound
quality.
Ifany
butlOn on the I/nit is pressed durinli the blackol/t lIlode,
The
.Iill1ction will
be
displayed
.IiJr
5 seconds to show the operation before
retuminli
ro
Blackout mode.
• Depending
on
the connected devices. some.IimctiollS
and
display
indications do not work.
Adjusting
Sound
Setting
in
Manual
Mode
You
can change these sound settings to create your own preference
when the MultEQ mode
is
set to MultEQ
off
(Manual Mode).
Use steps 1 to 4 to select one of the Sound menu
modes to modify. See the applicable section below for
details about the selected item.
1 Press
IMPRINT
to activate the Sound menu
selection mode.
30-EN
2 Turn the
Rotary
encoder
to select the desired Item,
and then press
~/ENT.
Subwoofer H
SUBW.
System*1 H
SUBW.
Phase*1 H
SUBW Channel*1 H Factory'S
EO
H
TW
Setup~
H
Filter Type H Media Xpander H
MX
Level*J H
EO
Mode H
TCR
Parameter H Sound
Field~
H Black Out H Subwoofer
(e.g. Select Subwoofer)
*1
These
jimctions
are inoperable when SI/bwoot'er is set to OFF.
*2 This jimction cun
be
operable only when PXA-H
loa
(sold
separately) is connected
and
2.2ch (3WAY) mode is set. For details.
refer
to the Owner's Manual
ofPXA-H
100.
*J
Thisfimction
is inoperable when Media Xpander is set to
OFF.
~
In
step
2,
three
sound
adjustment
iTems
(Parametric EQ/Graphic EQ,
T.Correction. X-Over)
am
be
selected
in
Sound
Field Adjustment
mode.
tum
the Rotary
encoder
to
seleCT
the desired
iTem.
lind
Then
press
~/ENT
To
cOnTinl/e
to step 3.
3 Turn the
Rotary
encoder
to change the setting,
and then press
~
lENT.
(e.g. Select Subwoofer ON or Subwoofer OFF)
4 Press and hold
~/ESC
for at least 2 seconds to
return to normal mode.
• Media Xpander. Factory's
EQ,
Parametric EQ/Graphic EQ
Adjustment. EQ Mode
and
MX
Level Adjustment are inoperable
when Defeat is set
to ON.
• Pressinli
~IESC
returns to the previous Sound menu
mode
.
• It'no operaTion is
performedfor
60
seconds.
Sound
menu
mode
is
canceled.
When the subwoofer is on. you can adjust the subwoofer output level
(refer to page 14).
OFF H ON (Initial setting)
When the subwoofer is on, you can select either System 1 or System2
for the desired subwoofer effect.
1 (Initial setting) H 2
System
1:
Subwoofer level changes according to the main
volume setting.
System
2:
Subwoofer level change
is
different from the main
volume setting. For example, even at low volume
settings, the subwoofer
is
still audible.
PHASE
00
(Initial setting) H PHASE 180
0
The subwoofer output phase
is
toggled SUBWOOFER NORMAL
(00)
or
SUBWOOFER REVERSE (180
0
).
To
adjust the level, turn the
Rotary encoder.
To Next Page
Loading...
Need help?
General
