Setting the Bass Level
3-3*5Turn the
Rotary
encoder
to select the desired
bass level
(-7-+7).
You
can emphasize or weaken the bass level.
4 Press and hold ~
lESe
for at least 2 seconds to
return to normal mode.
•
/fno
operation is
performedfor
/5
seconds. the unit will relllm to
normal mode automatically.
• The bass leve/ settings will be individually
memorizedfor
each
murce
(FM. AM. CD. etc.) until the setting is changed. The bass
frequency and bass bandwidth settings
adjustedfor
one source are
eiFective
for
all other sources (FM. AM.
CD.
etc.).
• Depending on the connected devices.
mme
functions
and
display
indications do not work. However, Bass Level is still adjustable
ifwz
audio processor with the Bassfunction is connected.
oj
When the subwoofer mode is set to
OFF,
its level cannot be adjusted.
Refer to "Turning Subwooler ON/OFF" (page /6).
0
4
The function is inoperable when DEFEAT is set to ON.
0
5
The adjustment can also
be
made by pressing Rotary
encoder
(AUDIO). Refer to "Adjusting Subwoofer Level/Bass Level/Treble
Level/Balance (Between Lejt and Right)/Fader (Between Frolll
and
Rear)/Defeat" (page /4).
Setting
the
Treble
Control
Yuu
can change the Treble Frequency emphasis to create yourown tonal
preference.
1 Press
SOUND
SETUP
to activate the Sound Setting
mode.
2 Turn the
Rotary
encoder
to select the Treble
Adjustment mode, and then press
~
lENT.
SUBW Level
oll
H
Bass
07
H Treble,7 H HPF,7 H Black Out
H SUBW Level
Sett"ng~~!,!reb~!<?e:rl~!r"Er~q~!B,~Y·.·
...
3-1 Press
BAND
to select the desired treble center
frequency.
10
kHz
~
12.5 kHz
~
15
kHz
~
17.5 kHz
~
10 kHz
Emphasizes the displayed treble frequency ranges.
Setting the Treble Level
3-2*XTurn the
Rotary
encoder
to select the desired
treble level
(-7-+7).
You
can emphasize or weaken the treble level.
4 Press and hold
~/ESe
for at least 2 seconds to
return to normal mode.
•
/fno
operation is
perfonnedfor
/5
seconds. the unit will retum to
normal mode automatically.
• The treble level settings will be individually memori:edfor each
source (FM. AM. CD. etc.) until the setting
is changed. The Treble
ji'equency settings adjusted
for
one source are effective
for
all other
sources (FM. AM.
CD.
etc.).
• Depending on the connected devices. some junctions and display
indications do
not
work. However, Treble Level is stilladjus/llble
if
an audio processor with the Treble junction is connected.
*6
When the subwoofer mode is set to
OFF,
its level cannot be adjusted.
Refer to "Turning Subwoofer
ON/OFF"
(page /6).
,7
The jimction is inoperable when DEFEAT is set to ON.
*X
The adju.wnelll can also be made by pressing Rotary encoder
(AUDIO). Refer
to "Adjusting Subwoofer Level/Bass Level/Treble
Level/Balance (Between Lett and Right)/Fader (Between Front and
Rear)/Defeat" (page /4).
Adjusting
the
High
Pass
Filter
The High Pass Filter on this unit can be adjusted to suit your personal
taste.
1 Press
SOUND
SETUP
to activate the Sound Setting
mode.
2 Turn the
Rotary
encoder
to select the High Pass
Filter (HPF) Adjustment mode, and then press
~/ENT.
SUBW Level,9 H Bass'lO H
Treble*1O
H HPF*IO
H Black Out H SUBW Level
3 Turn the
Rotary
encoder
to select the High Pass
Filter frequency.
OFF H 80 Hz H 120 Hz H 160 Hz
4 Press and hold ~
lESe
for at least 2 seconds to
return to normal mode.
•
/f
no operation is peljol1ned
for
/5
seconds. the unit will relllrn to
normal mode automlllically.
• When an
extema/audio
processor is cOlllzected. this setting cannot
be made.
0
9
When the subwoofer mode is set
to
OFF,
its level cannot be adjusted.
Refer to "Turning Subwoofer ON/OFF" (page /6).
oJU
The junction is inoperable when DEFEAT is set to ON.
15-EN
To Next Page
Loading...
Need help?
General
