Do
not
let
the
cable
be
entangled with
surrounding objects
Arrange
the
wires and cables
in
accordance
with
the requirements
of
the
manual
to
prevent them
from becoming obstructive while driving. Cables
or
wires
that
obstruct
or
hang on
the
steering
wheel, shift lever, brake pedal, etc. are extremely
dangerous. ·
Do
not
splice cables
Do
not
cut
the
cable insulation
to
supply power
to
other
equipment. Otherwise,
the
current
carrying capacity
of
the
wire will be exceeded,
resulting in fire
or
electric shock.
Do not damage
the
pipe
or
wiring when drilling
When drilling holes in
the
chassis
for
installation,
be careful
not
to
touch, damage
or
obstruct
the
pipes, fuel lines, fuel tanks
or
wires.
If
you
don't
pay attention,
it
can cause fire.
Do not use bolts
or
nuts in brakes
or
steering
systems
for
grounding connections
Never use bolts
or
nuts used in brakes
or
steering
systems (
or
any other safety-related systems)
or
fuel tanks for installation
or
grounding
connections. The use
of
such parts will cause
the
car controller
to
fail, resulting in fire and
so
on.
Do not install on
the
steering wheel
or
gear
lever, etc., which
may
hinder
the
operation
of
the
car
Otherwise,
it
will obstruct
the
front
line
of
sight
or
obstruct moving parts, etc., causing serious
accidents.
& Notice
This symbol indicates
important
instructions.
Fai
lure
to
heed these instructions may result
in
injury
or
major
property
damage.
When
there
is
a problem, please stop
us
ing
it
immediately
Otherwise,
it
may cause personal injury
or
damage
to
the
product.
Please
return this
product
to
an authorized Alpine dealer
or
the
nearest Alpine
se
rvice center
for
repair.
Ask professionals
for
wiring and installation
The wiring and installation
of
this product require
professional skills and experience.
Fo
r safety
reasons, please contact
the
dealer where you
purchased
the
product
for
installation.
Use designated accessori
es
and install securely
Make sure
to
use
only
designated accessories.
:he
use
of
non-designated parts may cause
internal damage
to
the
device,
or
it
may
not
be
securely installed in place. This can cause parts
to
loosen and cause danger
or
product failure.
Arrange
the
wires
to
avoid crimping
or
being
squeezed
by
sharp metal edges
The arrangement
of
wires and cables should be
far away
from
moving parts (such
as
seat tracks)
or
sharp edges
or
corners. This will avoid
crimping and damage
to
the
wi
res
.
If
the
wiring
passes
through
a metal hole, a rubber gasket
should be used
to
prevent
the
wire insulation
from
being cut
by
the
edge
of
the
metal hole.
Do not
install
in
high humidity or dusty locations
Avoid installing
the
device in a location wi
th
high
humidity
or
dust. Moisture
or
dust
invades
the
device and can cause
product
failure.
& Precautions
Product cleaning
Please use a
dry
soft
cloth
to
clean
the
product
regularly.
If
the
dirt
is
difficult
to
remove, soak a
soft
cloth
with
water
only
. Any
other
solvent may
dissolve.
Temperature
Before turning on
the
machine, please make
sure
that
the
temperature in
the
car
is
between
+60°C and -20°
C.
Maintain
If
you encounter a problem,
do
not
repair
it
yourself. Please return this
product
to
an
authorized Alpine dealer
or
the
nearest Alpine
service center
for
repair.
Installa
tion
location
• This machine cann
ot
be installed in any
of
the
following places:
• Near
di
rect sunli
ght
and heat
sour
c
es
•
Places
with high humidity and near water sources
• Dusty places
• Locations subject
to
severe vibration
2-
EN
II
To Next Page
Loading...
